20 Most Recent Maytag 30 in. CSG7000 Gas Cooktop Questions & Answers

yes you have to call the repair man.

Hi,Here is a tip that I wrote that will help figure out why the burner spark keepson clicking...Gas Range Repair Burners Keep on Clicking heatman101

Here in fixya we dont sell anything. However we have here a link with a part layout of your model wher you can also order the parts you need
http://www.appliancepartspros.com/partsearch/model.aspx?model_id=26037&diagram_id=28377040#d28377040

You will have to use a putty knife to separate the top from the burner box.
After you do your repair you will also need 107 inches of burner box tape to re-seal the top.

can you light them with a match and if so the gas is ok but the ignition moduel has failed. replace the moduel / other causes may be the switch harness . ck the switches and the wiring before replacing the oduel .. mm

I don't know, I did nothing, it just started working again??????

usually this is a problem with one or more of your ignitor switches, they are found below the selector switches, below the top, if you take off the selectors you might even be able to see them,
these are what sends voltage to you ignitor, from the spark module, one one goes bad, they all tend to spark, because light one light all....
http://www.appliancepartspros.com/part_details.aspx?part_id=4101545
this link wil take you right to the part i suggest,
as well as be able to order it

since this happens alot after a boil over i would start with one of the front two burners,,,, you can order one and keep replacing them with the next till the clicking stops

The problem is in the pilot ignitor Located under top, unplug the unit before replacing it. Write down all of the information ,mode, serial, and product number and name of stove. If you can get a part number, this would be very helpful. Take this to a local appliance parts house and they can help you.
Sincerely, shastalaker7

one of your electronic ignition switches is bad and burnt closed telling your spark module to spark
call applaince parts pro
1-877-477-7278
tell them u need part number
AP4101545 ignitor switch
18.00 dollars
they sit below the top under neaqth the selctors
you will have to go one by one
but the wires push in and pull out

its a gas cooktop it has to be plugged in somewhere op e the cabinet and unplug it. possible that the electrodes got wet and click from a false sense of continuity, after being unplugged overnight that will sometimes be enough. you also might have a bad start switch on one of hte burners causing the machine to click automatically. try unplugging over night first

othing Works, or the Oven / Range / Stovetop Works Only At Certain Times: 1. Home breaker flipped or the fuse blown? Possibly an electrical surge has flipped the breaker. Check your breaker or fuse box and replace or reset as necessary. 2. Power cord plugged in? Grab the plug and wiggle to determine a good connection. 3. Power cord damage? Damaged rubber with wires showing through or the wire is being pinched can cause issues. Electrical tape is acceptable for covering damaged wires. 4. A clicking sound could be something wrong with a relay. Check for any loose connections around the main control board on your oven. The click you hear is a relay losing power and switching back on. If the clock resets then something is causing power interruptions to the board. 5. 6. Even a bad relay door switch will hinder your oven from operating. If your oven has internal fuses, a wiring or component problem could have caused a fuse to blow. A blown fuse is an indication that a component has shorted or failed, and the problem will need to be corrected. Most ovens that use fuses will have an indication of the circuits that are affected by a particular fuse. If an oven fuse has blown, then you should inspect the oven element and the associated wiring to determine the cause before replacing the fuse ++++ Oven Control Board The oven control board has a set of relays that turn on and off power to the bake and broil circuits according to the customer settings and sensor input. If the oven won't turn off it could be that one of the relays on the oven control board is shorted closed, providing voltage to the heating circuit. It can be dangerous if the oven won't turn off. Don't leave the oven unattended without turning off power to the oven. Relay board: Some ovens are equipped with a relay board. This circuit board has several relays which control the switching of electrical current to the oven heat source. If the oven won't turn off it may be that one or more of the relays on the relay board have failed. If this happens replace the relay board. The relays on the board are not sold separately. ALSO CHECK THE BAKE AND BROIL ELEMENT.

Use this link for answers to all your cooktop issues.

Go to your electrical panel and check the circuit breakers. If one is tripped it will be in a halfway position. switch off then on. If it keeps tripping you may have to call a repair man.

First it could be leaking from the control knob when it is on . There could be a leak at the base off the burner letting out gas or on the burner line . You need to get back on to your installer or where you purchased the cook top . This basic gas fitting leak detection .

Sure. The wiring harness can be repaired or replaced as well as any damaged components.

Tammy have you checked the circuit breaker at the electrical panel of your home. Do the panel lights come on? If they do and the rest is off then it will need service.