Top 20 NorStar M7324 Telephone Questions & Answers

In order to help you have to include the make and model number of unit

Make sure you are playing the same greeting number you are recording

PDF]Telephone Features Programming Guide - Avaya Support

https://downloads.avaya.com/css/P8/documents/100142941 AvayaNORTEL NETWORKS is a trademark of Nortel Networks. ... All other trademarks and registered trademarks are the property of their ... One-line and two-line displays . ...Memory buttons . ... Call anomalies for telephones without line buttons . .... Select how you dial your calls . ... Receive a busy signal on an internal call .

Norstar How to program phone how to program voice mail ...

www.phonserv.com/1_PDF_user_guide_meridian_norstar_phone_syste...

Nortel Networks Meridian Norstar How to program voice mail phone feature codes ...Modular ICS KSU must be programmed with an M7310 or a M7324 telephone. ... Lift handset, press Voice Call key or press the Feature button, then press 66 2. .... At the LOG: prompt, enter your mailbox#(extension #. and your password all ...

[PDF]N QRTEL NORSTAR

Try dialing a 9 then the number

Good Morning Kim You can find the complete manual for the NorStar M7324 here https://www.broadconnect.ca/resource-centre/user-guides/nortel-phones/M7324-User.pdf Looking through a bit, you may be in an 'outgoing calls barred' state. which you may need to talk to your sys-admin about. See Page 14 of the document. There are also sections about logging in and logging off the phones later on. If your sys-admin has set phones so that they need to be logged into to make calls (perhaps to track long distance charges), then perhaps you are logged out. I hope this helps. Good Luck D

Try unplugging the power and the phone jack for a couple minutes and then reconnect.

to cancel intercom call forward press the call forward key again or feature #4 to cancel a line call forward choose the line and dial *73 or whatever the phone company's cancel call forward code is (may be in phone book)

Are you sure about the phone model number? Tone/pulse is set in the common equipment (KSU) configuration, not the individual set. Press Feature 9*80 to see the system software version.

press [Feature] # 86 to turn off Background Music (as Nortel calls it). F86 to turn on F#86 to turn off

Your expansion box is a CAP (central answer position) module. I will assume you are using the same jack as before. The line cord, from phone to jack should be 6 conductor (count pins on end). A short line cord runs from back of phone to back of CAP (plugs on CAP are labelled) then the longer cord runs from CAP to the wall jack.

Did it ever work in the past? That feature may not be supported on your model of phone or common equipment.

1. The line may be wired to a security system or fax. or 2. The IRAD (internal remote answer device) on the system may be answering that line.

It's a system programming option (via Feature ** CONFIG ) - the lines have to be set to "appear and ring" on that set. Not user set table.

press #68

the M7324 is a digital set, it will not work at home unless you have a system there also

Hi J, Do you mean how to make it ring when someone calls a specific phone number, or when someone calls the specific extension? If for a phone number, then you need the line to appear and ring on the phone. Let me know which one you're doing.

That might mean that the line(s) is(are) not programmed for that telephone. If you press feature * 0 then one of the line buttons, does it list as a line or blank?

I see the suggestions here are about programming a mailbox. If all you want to do is log in and you have the password, hit feature 981 and put in your password.

You are more than likely gonna have to go thru your company's IT person and have them update it to what you want. I am sure it is password protected.

press Feature *0 (button inquiry) then press the intercom key. When a set is installed it automatically gets an intercom #