20 Most Recent Hitachi UltraVision 55HDS52 Television - Page 4 Questions & Answers

What is the TV source or input? Unless the source is antenna or cable using the antenna in, the captions have to be disabled at the set-top box that is providing the signal. Some set-top boxes have a CC button on the remote but many have this hidden in the menu system. My IPTV box requires me to press Menu, choose the Settings menu and then enter a code provided by the provider. Once in the menu, the captions are enabled in the Hardware > Audio menu. Some satellite dish set top boxes have different access methods depending on the TV setup. If you have a master box that feeds two TVs, the setting menu to control the closed captions was only available on the TV closest to that box. (This was the case for a Dish receiver with a Single or Dual mode. In single mode, turning on the CC enabled the captions for both TVs. In dual mode, the two TVs could be tuned to different channels but only the TV nearest the set top box would display the closed captions if the feature was enabled. On that receiver, the closed captions were reached by pressing Menu. Then the captions options were under Properties > Closed Captions.) Please indicate what the TV source is for further information on where the sub-menu for the closed captions will be toggled on and off. I hope this helps. Cindy Wells

Help my closed caption option is not highlighted how can I remove CC from my Hitachi tv?

charger failure

buy a remote or fix the button

what are you using for the input? cable or antenna

probably a back light issue

If you wish to get some details; check the site linked here. Pull up older posts. https://electronicshelponline.blogspot.com/ https://elektrotricks.blogspot.com/ faults & possible causes to LCD & Plasma screen are given with illustrations. You can get an idea about the fault to an extent. Search the site by type in the brand name of your set, in its search bar at the right side column, and press enter.

Try resetting the power by switching off the TV and then switch off the TV's power outlet and disconnect the TV's power cable from the outlet. Press and hold the TV's Power button for about 30 seconds to drain any residual power from the TV and then release the button. Turn on the TV in the normal manner and see if it turns on then afterwards.

If it works, put it on Facebook MarketPlace, free to collector. If it doesn't, you might be able to split it in the middle. https://www.cnet.com/reviews/hitachi-51swx20b-review/ ..

Replacement screen is required, so a new tv is probably cheaper.

You would need the remote control to select the MENU, then LANGUAGE.

Use code search on your Sudden Link URC to find something that woks. If a search through all codes stored in the URC fails, try a different one.

I am guessing it's an old(ish) TV. As a plasma the chances are that it is on it's way out. Please Try new cables (HDMI etc)

I don't know but it probably isn't much different to most other tv/remote combinations where commands are given by the remote and carried out by the brain in the tv. Start by pressing the Menu button and the main menu should appear onscreen and from there use the up, down, left and right buttons to navigate the main menu and the select button to select sub-menus and items from the menu(s) until you reach the section on channel search, installation, etc.

Did you know that this site https://fmovies.dev updates movies frequently and you can watch them for free?

If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/ Faults & possible causes to LCD screen are given with illustrations. You can get an idea about the fault to an extent. View the site by desktop or web view on mobile devices to see the "search box". Type in the brand name of your set in search box; to get gathered the related posts. Screen-shots to defective LCD panels are given. You can see and compare to that to your TVs', and can make sure about the fault to an extent.

First make sure that the current Source or Input is set to TV. This is usually the only reason for the error message you see. To select the source, look for a Source or Input button on the original remote. If you have an universal remote with a button with the Source/Input label, you may need to try alternative codes to make the button work. (Power and channel controls will often match across multiple codes for the TV manufacturer.) Alternatively, check if there is a Source/Input button on the TV or a section of the menu system with the function. Once you set this source, try again. Note: there was a period when manufacturers sold some TVs without tuners. They were labeled HD-ready sets. These can't do a channel scan and do not have an RF antenna jack on the set. I hope this helps. Please add a comment with the model number of your Hitachi TV for more information on setting the source on your set. Cindy Wells

Under Audio or Audio Settings on the on-screen menu, TV Speakers is set to On. All of the cables physically connected to the TV and the input devices are secure. Switch to a different input device and verify there is sound from the TV speakers (for example, a DVD player or a gaming console). https://www.ifixit.com/Answers/View/310570/The+sound+on+my+TV+stopped+working.

look on the back of the television and the DVD player, there should be a SCART socket and/or red, white and yellow AV sockets, either use a SCART lead and connect it to the SCART on the DVD player and the TV.Or use an AV lead with 3 auxiliary shape connectors and match the colour of each connector with the female sockets on both the TV and the DVD player instead of using the other component connections.

The quickest way would be to turn TV off and then turn TV back on again.