LG 24 in. LDF 7811 Built-in Dishwasher - Answered Questions & Fixed issues
Lg 3850dd3006e makes noise
I had the same issue with my LG it has a stainless steel impeller the grinds up the food particles and if one of the veins get slightly bent it causes that problem. The tack took it out straightened it out until the new part arrived and it worked fine. He did return to replace it but I don't think it was needed
Makes a whistling noise when in use
I had a problem with my LG dishwasher and there was a small stainless steel impeller that they had to replace to stop the high pitch noise. I think this impeller grinds up any food particles. The tech said if one of the veins bend it causes this issue.
LG ld-14aw2 dishwasher
IE is inlet error, displayed when "Not reached to the normal water level in spite of 10 min. water supply"
Possible cause:
- The Water Supply Tap is closed.
- The Water Supply is shut off.
- The Inlet Hose is kinked.
- The Water Pressure is very low.(below 10 psi)
- Inlet Valve is OK?
- The filter of Inlet Valve is clogged by impure water.
- The Hall sensor is OK?
- The Impeller of Air Guide is bound.
Remedy:
- Take action on Water Supply device.
- Measure the electric resistance of Inlet Valve. (950-1300 )
- Clean the filter of Inlet Valve.
- Check the frequency of Inlet Water by the Test Mode.
- Replace the Air Braker.
LG LD14AT3 DISHWASHER SHOWING E1
Hello, ivt
I was trying to help
you out here. I was going back to some customers that asked questions
in the past and it appeared that no one answered them, so I thought I
would take some of my personal time to see if I can help. Even though
this site may not have your exact model or brand, This link will help
you tons. Here is a link
to about everything you want to know about your dishwasher, from repair
to trouble shooting it,pictures, video's. Just scroll around and you
will see tons of information to almost any question you might have on
your dishwasher. If you go to this link and click around, I am sure you
will find out so much about your dishwasher, you will know more that the
company that made it. Here Is the link for you to click on>>
http://home.howstuffworks.com/dishwasher.htm
Please if this helped you at all, if you can find the time
to rate my help and some kind words written would be appreciated for my
free help , I would appreciate it. Here is also my direct link to my own
pages of other areas of my expertise for other problems you might have
in Automotive,Appliance, and Electronics. Drop In anytime for my help.
Thanks,Mike
http://beta.fixya.com/users/mc1bean
Displaying code IE
Hi jakkirker,
The IE error you are seeing means Inlet Error, this shows because your dishwasher is not getting
enough water through in a specific time frame - Please check the following:
- Is the Inlet hose kinked in any way? (This could lead to low water pressure to the solenoid) Straighten it.
- Is the Inlet hose filter (Found when unscrewing the hose form the inlet on the machine) dirty? Clean it.
- Is the tap completely open? (Low pressure)
- Has your home gone under any plumbing alterations? (This could have also caused low water pressure - Too little water)
If
all of these come back OK, and it still gives the same problem, I'd
suggest replacing the inlet valve (Found on the opposite side of the
inlet pipe - inside your Dishwasher), could also be a pressure switch
(Found at the bottom of your Dishwasher - accessible from the bottom).
This should solve any problems.
Kind Regards :-)
Jedemeyer1
* If you found this solution helpful - please rate it
Lg dishwasher 14aw2
Says 0E
Dishwasher still
Dear Jester Stanf,
Your drain pump may not be working anymore. Check the outlet hose and let it lie on the floor to drain most water out of the dishwasher, then remove the Top Panel (fastened by 2 screws at the back) and then the side panels. A normal Dishwasher should be attached to the sump.
You can test it by applying direct power to it, its alternating current so it doesn't matter which pin you attach live to and which neutral. If it turns, then inspect the machine for a loose wire towards the pump, if it does not turn sideways, or does it strangely then replace the pump. You can get it from a reputable appliance spare outlet.
Kind Regards :-)
* If you found this solution helpful, please rate 4 thumbs up and leave a small testimonial. :-)
Hi there,
We have a LD-14aw2
Hi,
I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works like new... However I have also foundthat if the heating element goes bad then that also can mess things up bad...So I would buy new spray arms, and also check out the heating element to makesure it is working... Here is a tip that will help you with the onlinebuying...
Dishwasher
SprayArms not Spinning
How to Buy
ApplianceParts OnlineA bad heating element causes many problems in dishwashers...
Dishwasher Problems The
HeatingElement not WorkingDishwasherMaintenance
DishwasherResidue and Film on Dishes
heatman101
Asker's Testimonial "explanation very clear. will give it a go and see howsimple it was. thanks Ronnie " - ronnieshomes
Hi
I have an LG
Hi
Error
code IE on LG dishwasher means Inlet error. This error comes up when the Water
Supply Tap is closed or Water Supply is shut off. If water supply is turned on
then make sure that the Inlet Hose is not kinked and water Pressure is not low
(should be above 10 psi). Next thing to check for is Water Inlet Valve, measure
the electric resistance of Inlet Valve. (950-1300 ohms) Make sure the filter of
Inlet Valve is not clogged.
Hope this helps... Please post back
for further assistance.
Daniel
ADJUST TENSION DOOR
Just below dish loading door there is a panel. Remove screws (if applicable) to find tension adjustment. Turn screw to the left to loosen or opposite lifting door open or closed untill happy with tension. Some washers have no adjustment, I suggest opening door fully and pulling out bottom load tray, loading and then top tray or rack, pushing top in first then bottom rack. Use a glass fry pan cover or fry pan for weight on door while filling soap. Good luck, best regards
My LG Dishwasher model LDF7811WW was getting
Hi
Thanks for using FixYa. Error FE in your Dishwasher indicates excessive
water is supplied than the normal water level. If the dishwasher is overfilling it's caused
because of water-inlet valve going bad. This valve is usually at the bottom
left or right of the dishwasher, behind the lower access panel. It's the device
with the main water line from the house, a rubber tube to the dishwasher, and
two wires attached to it. If the water-inlet valve is defective, you need to
completely replace it. Please accept the solution if the issue is
resolved or post a comment for further assistance.
Thanks
Rylee
Top arm in dishwasher will NOT spin!
When you say the top arm does not spin, remember that the LG model x811 family has the Vario feature that alternates between routing the pumped water to the bottom arm and then the top arms alternately. So anytime the dishwasher is washing and rinsing, either the lower or upper arms will be spinning.
If the problem is not above, then the motor that drives the check valve may have failed (or the check valve is obstructed inside.)
Hope that helps. Please post back here with what you find, OK?
LG dishwasher always smells moldy
could be a very small leak with the hoses leading into the washer, there is insulation around the washer that is a breeding ground for mold. I would recommend you have someone with decent mechanical experience, doesn't need to be a plummer just someone who knows how to use tools, pull the washer out refit the hoses with new seals and replace the insulation. Also the vinegar does work to help clean your washer, it removes calcium and other mineral build ups throughout the washer.
LG Dishwasher LDF7811 Making Growling Noise
Recommendations:
-Switch to a brand name detergent powder - like Electrosol or Cascade and do not fill the dispenser cup full. You will notice the difference immediately.
-Remove the filter assembly one more time and inspect underneath with a flashlight. Look closely for debris and also inspect the impeller to look for damage and that it is spinning freely.
Reassemble and listen for the growling sound. It should not happen. If it continues, you may have a a failing wash motor / motor bearing.
Please report back what you find. OK?
4/16/2009 2:14:01 AM •
LG 24 in. LDF...
•
Answered
on Apr 16, 2009
•
3,861 views
Upper rack sprayers not working on LG ldf7811 dish washer
Check the pump out. Even though the Hose is and tubes are clear it does not necessarily mean that the pump is not pumping water to the top sprayer. One way you can do this is take off the upper spray tube and lay it in a glass or bowl and turn on your machine for a minute or so to get the water flowing if it flows then I would take off the spray assembly itself and make sure that there is no blockage on the bearing race
4/17/2009 10:06:59 AM •
LG 24 in. LDF...
•
Answered
on Apr 17, 2009
•
1,259 views
Hi. I have a 3
Measure the electric resistance of the Drain Motor. (Value should be 20-40 Ohms) If it is out of spec, replace it.
Please reply with what worked best. Thanks!
Not finding what you are looking for?