LG Jabra A210 Bluetooth Adapter for Headset - Answered Questions & Fixed issues

I had not used my A210 in a couple years, and when I needed it again now, I TOO GOT THIS SAME EXACT SYMPTOM: where it would light red (charging) only for 2 or 3 seconds, and then be off. Hours on the charger and no charging or difference. I tried plugging it in a few hundred times to see if it would "jump start" for the 3 seconds to add up, no luck. I WAS VERY GLAD to read MightyFrosty could change something inside and get it working. I followed his advice up to "removing the tiny circuitboard on the tiny battery and resoldering". Instead (got the case open with a razor blade, gently) I removed the amber tape that wraps the battery/circuitboard assembly and tried first "jumping" the red to the "+", nothing~ but then jumping the black to the "-" the RED LIGHT came on and STAYED ON! (but only while "jumped". Better yet after some 20 minutes of "jumpered" charging, the RED LIGHT STAYED ON even when I removed the tiny jumper~! (a tiny wire is all, bent to touch the black wire solder spot and the "-" battery lead). so IT APPEARS it CAN CHARGE PROPERLY on its own once the battery has a little juice in it! It is charging completely normally now (red light solid, no jumpers, and with no cuts or circuit removals!). I believe I can reassemble it all tomorrow and have a non-modified operational bluetooth Jabra! Thank you MightyFrosty and good luck to all!

No, they can't.

hi,
you have to connect the jabra audio jack to the audio source, to the speaker output of your receiver for example. If jabra detects the source it will work. If you cut the connection, jabra watch for a while if something happend and than stops the transmittion. Hope that helps

My solution is to connect the jabra audio jack to the speaker output of my receiver. Jabra need it to detect a source. If the connection to the source is cut, jabra waits around 30 seconds and if nothing happend jabra stop the transmittion. I hope that helps.

the cover is a little rubber covering on the side you lift with your fingernail, and the charger port in underneath.

I had the same issue. So what I did was get a small screwdriver, opened the A210 case removed the battery. You will notice orange tape (remove it) then attached to the battery is a small board (the defective part) . Cut away the board, then you will need to solder the wires back to the thin metal film leads. And voila it will now charge, make sure to never let it charge for more than 2 hours. Do this at your own risk. Of course this will void the warranty.

I contacted Jabra and they said this problem is due to a bad internal battery. There is nothing that can be done to fix it. So I returned it to the guy who sold it to me and got my money back. Purchased another from a different vendor, and this one works great. That's the only solution!

If the LG Tone Infinim HBS900 is not pairing with your Apple iPad, there are a few things you can try to troubleshoot the issue:

1. Check the Bluetooth settings: Make sure that Bluetooth is turned on and that the LG Tone Infinim HBS900 is in pairing mode. To put the device in pairing mode, press and hold the power button until the LED light flashes blue and red.
2. Check for software updates: Make sure that your iPad has the latest software updates installed.
3. Check for other connected devices: Make sure that the LG Tone Infinim HBS900 is not already connected to another device. If it is, disconnect it from that device before trying to connect it to the iPad.
4. Check the distance: Make sure that the LG Tone Infinim HBS900 and the iPad are within close proximity to each other. Bluetooth devices typically have a range of around 30 feet.
5. Reset the LG Tone Infinim HBS900: Hold down the power button for 10 seconds, release, and then hold it down again for another 10 seconds.
6. Reset the iPad's network settings: Go to Settings > General > Reset > Reset Network Settings.
7. Check if the device is in pairing mode, if not activate it.

If none of the above steps resolve the issue, you may need to contact the manufacturer or a professional technician for further assistance. It's recommended to check the user manual of your device before trying any of the above steps, as the process of troubleshooting the pairing process can vary depending on the model and manufacturer.

have you replaced battery? 1. charger is not working 2. battery is bad.

You can't use bluetooth headphones,

Believe this or not, I had the same problem. The fix... Cleaned out the ear wax from the hole that got packed in there on my first use. No kidding. Hope that solves our situation.

if check both voltage and current rating both are same no problem can connect

resolder one in

sould't be doing this

You need to replace the battery in the headset.

i had to find the stereos max address download a bluetooth direct app and use it and musicflow bluetooth simultaneously on moto z3 hope this helps

take it back and have it examined under warranty

What is wrong with it?

Really poor choice of words. I understand you are frustrated. The speakers need to be charged or take batteries. There should be a charging jack. When the unit is charged and turned on, you can go to your phone and activate the Bluetooth and you should be able to see the speakers on a list of detected blue tooth device. Select that device and see if it asks for a KEY. If it does then you can look for a label on the speakers or google the model number.

On the Android Google cell phones, you can download an APP called WiFi Analyser. Perhaps iPhones have a similar APP available? Now you can see a display of all the WiFi traffic around you. With this choose the least busy channel. The next advice is to put the device on your LAN that does the WiFi in a clear space and high up in your premises. This gives you all the chance you have of getting a better signal. Now do the same for your JBL box within reason.