20 Most Recent Konica Minolta bizhub C250 All-In-One Laser Printer - Page 8 Questions & Answers

no such code Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Abnormality is detected by the abnormal check of each NVRAM Data. Non Volatile Read Access Memory, Will need a tech for this os failed or the NVRAM chip failed, tech mite try to re-flash os, Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

replace fuser unit power off the on Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Main Motor failure to turn. Remove all the image units then shake each one side to side. What you want to do is spread the developer (Located inside the unit) along the entire length of the image units. BET a all the image unit was stored up & down, instead of flat, person just picked it up and installed it. All the developer was sitting at one end so the motor could not turn correctly. NEVER EVER STORE I/U UP/DOWN always flat!!! Open & close the front door to reset the code. If code comes back then you might have already burned out the motor, or worse case the Control board went bad. But first replace the image unit with a new one cheaper. Cheaper, then having a Technician come out to check the motor and control board. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Fax board issue Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

bad magenta unit replace it. The other cartridges are new ??????. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Sir/Mam, You hit a serious code, noting can be done, this code requires a tech to come out and remove a chip inside the machine, which is then sent to Konica Minolta, then on to the US SECRET SERVICE since someone attempted to counter fit US currency!!!!!!!!!!!, until the US Secret Service determines what was done the machine stays inoperative , once what happen is determined tech will come out reinstall the chip reload firmware, and .NEVER EVER PLACE ANY CURRENCY ON A COPIER all the machine now a day have Bank Note chips. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

GO into printer properties select left binding, and double side copies Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Internal power supply need checkup to insure satisfactory power and stability

Make sure the fuser assembly is ok

What is the arp request????? Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Self Help Product Support Konica Minolta Business Solutions Inc Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

no such code Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

check print properties on computer, double side and left binding Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Main Motor failure to turn, PROBABLE CAUSES: 1. The main motor (M1) has failed. Replace M1 (p/n 4038 M101 00). If the problem persists replace PWB-M (p/n 4038 0101 05 for bizhub C250 and p/n 4038 H001 01 for bizhub C252 Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

most of the time requires replacement, Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

open right side remove two screws which release locks one to the rear on to the front, pull belt assy out, install new one reinstall locks Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

right side of the machine open right side cover look inside the machine see the shiney belt, well right above that is big assemble, that is tthe fuser Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

replace the black image unit Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

what about it Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f