20 Most Recent Konica Minolta bizhub C250 All-In-One Laser Printer - Page 7 Questions & Answers


third draw lift failure

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Jun 24, 2016


Sir/Mam,
Main Motor failure to turn. Remove all image units then shake each side to side. What you want to do is spread the developer (Located inside the unit) along the entire length of the image unit. BET the image(s) unit were stored up & down, instead of flat, person just picked it up and installed it. All the developer was sitting at one end so the motor could not turn correctly. NEVER EVER STORE I/U UP/DOWN always flat!!! Open & close the front door to reset the code. If code comes back then you might have already burned out the main motor, or worse case the Control board went bad ($$$$$$$$$$$$$$$). But first replace the image units (all one might be stuck or two or three or four) with a new one. Cheaper, then having a Technician come out to check the motor and control board.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Jun 24, 2016


For which color did you replace? because you are dealing with a color machine C250 that is part of the image unit so which color??

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Jun 24, 2016


Try 12345678.  That worked for me for my Bizhub C250.

Konica Minolta... | Answered on Jun 21, 2016


no such counter m1?

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Jun 19, 2016


replace the black image unit

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Jun 18, 2016


Abnormality is detected by the abnormal check of
each NVRAM Data.


get tech out re-flash copier software

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Jun 18, 2016


no such in the service manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Jun 18, 2016


no such code

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Jun 18, 2016


Abnormality is detected by the abnormal check of each NVRAM Data. Non Volatile Read Access Memory, Will need a tech for this os failed or the NVRAM chip failed, tech mite try to re-flash os,

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Jun 18, 2016


replace fuser unit power off the on

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Jun 18, 2016


Main Motor failure to turn. Remove all the image units then shake each one side to side. What you want to do is spread the developer (Located inside the unit) along the entire length of the image units. BET a all the image unit was stored up & down, instead of flat, person just picked it up and installed it. All the developer was sitting at one end so the motor could not turn correctly. NEVER EVER STORE I/U UP/DOWN always flat!!! Open & close the front door to reset the code. If code comes back then you might have already burned out the motor, or worse case the Control board went bad. But first replace the image unit with a new one cheaper. Cheaper, then having a Technician come out to check the motor and control board.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Jun 18, 2016


Fax board issue

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Jun 17, 2016


Sir/Mam,
You hit a serious code, noting can be done, this code requires a tech to come out and remove a chip inside the machine, which is then sent to Konica Minolta, then on to the US SECRET SERVICE since someone attempted to counter fit US currency!!!!!!!!!!!, until the US Secret Service determines what was done the machine stays inoperative , once what happen is determined tech will come out reinstall the chip reload firmware, and .NEVER EVER PLACE ANY CURRENCY ON A COPIER all the machine now a day have Bank Note chips.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Jun 17, 2016


GO into printer properties select left binding, and double side copies

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Jun 17, 2016


Internal power supply need checkup to insure satisfactory power and stability

Konica Minolta... | Answered on May 30, 2016


Make sure the fuser assembly is ok

Konica Minolta... | Answered on May 30, 2016

Not finding what you are looking for?
Konica Minolta bizhub C250 All-In-One Laser Printer Logo

1,252 questions posted

Ask a Question

Usually answered in minutes!

Top Konica Minolta Office Equipment & Supplies Experts

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6850 Answers

Adorjani Laszlo

Level 3 Expert

1316 Answers

George Mclaughlin

Level 2 Expert

364 Answers

Are you a Konica Minolta Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

bizhub Konica Minolta

  • bizhub Konica Minolta

Most Popular Question

clear error message c 2558 konica

  • Office Equipment & Supplies
Loading...