20 Most Recent Konica Minolta bizhub C250 All-In-One Laser Printer - Page 2 Questions & Answers

was told this message meant Konica have disabled the machine remotely.

machine trouble sevice call [c2558] wat a problam in konica minolta bizhub 164 printer

what lamp error

Hi this kind of errors how came u should mention frst may ne after you removed the board and then came ? or while working suddnetly came ? please specify

Sometimes just open the doors and closing them a few times will work its sensing somethings open ,Make sure all is closed you may have too reinstall drivers. start over read all directions sometimes we get burnt out on trying to get something going give it a break for a bit then try again. could be a firewall or anti virus cause problems to.

Are you using a 3rd party image unit???, if so get OEM there are chips on them that copier monitors. The image units are the units below the toner cart. which one is having the problem Y M C or Black, did you re chip them, bad idea. Replace them with OEM cartridge. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

tis error means abnormal tonder density in the balck image unit take the blacke image unit out and shake it while holding it level and put it back in the machine to reset the error code leave the machine on and open then close the front door

Does this happen when copying? Can you print internal copier form meter count etc.? Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Hope this helps. Make sure you remove the waste tank prior to taking out the transfer belt. Belt is removed by two screws inside right door and sliding the unit out.

Turn OFF the Main Power Switch.

2. Turn Main Power Switch ON while pressing the Utility/Counter key. (Sub power must be "on" located on side of the control panel)

3. Touch [Trouble Reset].

4. Check to make sure that [OK] is displayed and the it has been reset.

5. After turning off the Main Power Switch, turn it on again more than 10 seconds after

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

There is no procedure to restore the admin password. It is possible to reset and enter a new password, and for that you will need a technician to make the adjustments on SERVICE MODE (stop,0,C).

no such code for a C250 Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

1. Turn OFF the main power switch. 2. Turn main power switch ON while pressing the Reset key. 3. Touch [Trouble Reset]. 4. Check to make sure that [OK] is displayed and it has been reset. 5. After turning off the main power switch, turn it on again more than 10 seconds after and check if the machine starts correctly. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Its looking for the fax board ??? Some one remove it???? Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

NVRAM error when the main board was replaced was the NVRAM module replace was this a new board or one from a different machine if so you machine is junk. Have tech come out to re-flash firmware get a new board etc if he can Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

the control board can not talk to the hard drive was the hard drive replaced? Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

see the previous post sir mam Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

You must have access to the a secure KonicaMinolta web site, need a tech to come out Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

your bottom paper draw will not go down. release the draw via manual mode small hole in the back, un plug machine and use a screw drive and push it in the hole to release the draw Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

sir Memory is missing might have been removed or the the memory is not seated properly, Or it is bad worse case the board the memory is on is bad$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f