Top 20
Minolta C350 Printer Questions & Answers
Konica c350 c0016
Sir/ Mam Your Black PC Drum Motor is failing to turn. 1. open close front door to reset. If that does not work remove the black image unit and shack it side to side we want the developer inside the I/u to spread out along the entire length of the I/u not all sitting at one end of I/u that make the motor have a difficult time trying to turn. All I/u boxes should be stored horiz. not vertical. Btw, I’m available to help over the phone in case u need at
https://www.6ya.com/expert/normanj_7893313f0751935f
Recent Driver Answer
kmbs.konicaminolta.us
In the top right corner you will find the downloads link. You will find all available drivers. The C350 is a older model and there my not be drivers available for newer version computers.
Image drum unit
Remove the image unit that the operating screen indicates then install the new one don't for get to pull the protective sheet once the image unit is installed Also en sure to shake the image unit There is what is called developer inside it shake I/U side ways to spread the developer along the hole I/u if not and all the developer is sitting at one end when the motor for that unit turns you will get a code or burn out the motor, Btw, I’m available to help over the phone in case u need at
https://www.6ya.com/expert/normanj_7893313f0751935f
C0016 retraction
Black Image unit Motor failure to turn. Remove the black image unit then shake side to side. what you want to do is spread the developer (Located inside the unit) along the entire length of the image unit. BET the image unit was stored up instead of flat, person just picked it up and installed it. All the developer was sitting at one end so the motor could not turn correctly. NEVER EVER STORE I/U UP always Flat!!!. Open & close front door to reset. If it comes back then you might have already burn out the motor, worse case the Control board went bad. Btw, I’m available to help over the phone in case u need at
https://www.6ya.com/expert/normanj_7893313f0751935f
Not making copying and show error code no c-0098
Try reset the error code.Turn OFF the copier,press and keep pressed the Utility key turn ON the copier wait to display appaire the Trouble reset message.Release the Utility key,touch the message and turn OFF the copier.Wait 1 minutes and turn ON.
My Konica-Minolta-Bizhub-C350-Color-Copier-Printer paper keeps jamming, why?
well could be several reason incorrect paper size incorrect paper weight are you running Thick 1 or Thick 2 to paper. Do you know how to read paper weight? on out side of the paper package is words 20lb or 36lb mite also see the something like 75 g/m2 that is the weight of paper in the metric world (Every one else except the GOOD OLD USA.:):):) we use the lb. system . select paper on the control panel and make sure the paper weight matches most paper copy are putting both lb. and metric but if it is only metric then use the control panel to figure it as you select the thick 1 or 2 you will see the g/m2 on the control panel, if you using paper off the shelve and don't know then call the company where you get the paper from and ask them. Are using the bypass tray make sure that you follow the icon on the screen when it says load paper in the by pass tray does the little icon show portrait or landscape. if you using legal size paper did you pull out the extention tray to allow additional sensor to come into play for the longer paper. Does you print properties on the computer screen match what is in the draws? IF the paper come wrapped an only has lb. # then you will not find it on the control panel you need to get your operation manual out in that manual will be a chart that show what lb. # equals what thick 1 or thick 2. Btw, I’m available to help over the phone in case u need at
https://www.6ya.com/expert/normanj_7893313f0751935f
BIZHUB C350 code C-0208
You need to replace the drum-corona wire assembly. It is a consumable part, but it is a bit more complicated than just replacing a toner cartridge. You will have to determine which color the bad drum is associated with as well.
Hi guys i am saeid from iran.my problem is:i
Having got the details o the problem you posted, i would like to give
you the detailed guided step by step clicks you carry out now to fix
this problem and get the whole of your pc fast running again.
Its the
COMPUTER HELP TEAM PROJECT
Follow up the experts detailed guide to ix the errors with your pc.
Access the platform for fixing all pc errors and optimizing your pc speed
HERE
Step 1. success.
How do u fix a
Is this error shown when you try to print or when you try to copy? If it shows up when you try to print, then have you set any username and password to copy? Awaiting.
As a solution fails in minolta c350 code c-0060
Fusing drive motor failure, replace the fuser recently? (THE HOT PART) there is something jammed the fuser can't turn, orange looking rollers about 12" long, on the right side of the machine. above the transfer belt. Hopefully the motor is not burned out worse case the moor is burned out and that took the control board $$$$$$$$$$$. Open close the front door to reset Btw, I’m available to help over the phone in case u need at
https://www.6ya.com/expert/normanj_7893313f0751935f
Hello !
Hello!
Please state your question or problem so that we may help.
Not finding what you are looking for?