Top 20
Polaroid FLM-3732 Television Questions & Answers
Please help my Polaroid 37" lcd
Sounds like The main power supply regulator section circuit fault. Either it will be a separate board, or the part of main board. Check and replace damaged component/s at its main power regulator [SMPS] section circuit. Contact any service technician. If you wish to get some details; check the site linked here. Pull up older posts.
http://electronicshelponline.blogspot.com/ It will be best to replace the power supply regulator board as card basis rather than making "Surgery" to it; which usually will make loss for both money and time. Even though you can make it right, it will cost around an amount equal to the cost of a new board; including the cost of (spare parts + service charge) More to say, most of the spare parts to it will be difficult to get from open electronic spare part market. This is true to most of the flat panel TV power supply boards; irrespective of its brand and screen size.
Search the site by type in the "brand name" to your device; in the "Search box at the top right of the display window of the Homepage" to get gathered related posts.
3/8/2017 10:51:03 AM •
Polaroid...
•
93 views • 0 helpful votes
Polaroid 373b Blues!
what does the board look like in same area as black arc spot on case (damaged??) the high pitch whine you hear is the high freq switching going on in the electronics , this by itself is not too bad ( I had an old floursent clock that whined so loud it made my dog howl !! and it still works !! ) but when it accompanies a non functional device id say the power supply is straining to provide power (over loaded)
3/4/2017 1:30:03 AM •
Polaroid...
•
73 views • 0 helpful votes
Cable cord broke off back of vizio tv other ways to get cable
Replace the cord or watch TV at a relative's house.
Seriously, If you cannot replace the cable, your cable company will repair it for you. Probable for free - especially if you say you need to cancel your subscription unless they do it at no charge.
5/19/2014 10:03:00 PM •
Polaroid...
•
48 views • 0 helpful votes
How could i fix my tv
The back-light inverter board should be checked. Check the voltage that comes to that board, from the TVs' main power supply regulator board. You should have a digital multimeter to measure these voltages. If you wish to get some details,
http://electronicshelponline.blogspot.com/ Pull up older posts.
12/15/2013 4:45:42 AM •
Polaroid...
•
113 views • 0 helpful votes
Everything works....After 5 minutes, no sound.
Check and replace its audio output IC, or audio output card. If you wish to get more details, check this link.
http://electronicshelponline.blogspot.com/ Selecting the view option, either to
Mosaic
/ Time slide, can be selected by the
drop-down list, at the top left
of the display window, will make surf easy. You can also do a search, by type in the brand name/model
number/IC used, in the search box at the top right of the display window.
10/27/2013 3:38:25 PM •
Polaroid...
•
40 views • 0 helpful votes
Polaroid 3700 lcd
GOT SAME PROBLEM NOW IS THERE A FUSE WHERE POWER CORD PLUGS INTO THE SET ON THE BACK MINE HAS A GLASS FUSE NEXT TO THE PRONGS THAT COME FROM TV YOU HAVE TO USE A SCREW DRIVER TO POP IT OUT SHOWS A PIC OF IT IF YOU DON'T SEE IT DON'T TRY TO POP IT OUT
2/24/2013 6:59:58 PM •
Polaroid...
•
201 views • 0 helpful votes
Tv turns on no picture no sound i think its the remote
Its more than likely the board issue if the power light lights up but yet the set is dead with no sound or video. That could be either a power supply issue or a main board issue, and will require troubleshooting to determine if its the power board or is it the main board not sending the power on command. I would try
www.tvrepairworld.com for assistance as they can help you determine which board actually has the issue.
1/1/2013 6:54:50 PM •
Polaroid...
•
55 views • 0 helpful votes
What are 2 blown casps in a polaroid tv, and how can you fix them?
Did you get a estimate or what? CAPS will have a value and voltage rating marked on them as well as a location number on the circuit board which is a reference to them as parts in the parts list for the set.Filter caps often puff up when they fail,,two leads each and soldered into a board---here are what some bad caps look like.
arrows point to extreme examples of puffed up caps that are bad.
6/11/2012 2:23:43 PM •
Polaroid...
•
136 views • 1 helpful votes
How you programh the memory
Are you trying to program channels into the memory of the set?Should be done with the original remote in the main setup menu.
5/1/2012 1:07:32 AM •
Polaroid...
•
25 views • 0 helpful votes
Polaroid flm-373b lcd tv - making a loud buzzing
Possible that the main power supply unit which is the SMPS- switch mode power supply- has a faulty capacitor or in the INVERTOR board which has changed the value and so the frequency being changed can cause higher huming level- reduced to lower frequency.
so check the board for leaks , if so replace. Also check if the threshold voltages are below level in these circuits. if so the capacitor can be identified. If there is change after the component heats then simulate the circuit board and confirm using a hair dryer.
9/23/2011 5:12:34 AM •
Polaroid...
•
191 views • 0 helpful votes
Not finding what you are looking for?