20 Most Recent Frigidaire AEQ7000ES Dryer Questions & Answers

0helpful
1answer

Error code DR

Pull the tech sheet out of the dryer ( behind the lower front access panal ). The lights flashing are trying to tell you a fault code.

A copy:

MODEL DIFFERENCES: • Better models have a digital readout display
• Good models do not have a digital readout display
READING ERROR CODES 1. Position cycle selector knob to the 3 O’clock position.
2. Press and hold the Select and Pause Cancel buttons simultaneously for six seconds.
3. Immediately after, press and hold the START and Pause Cancel buttons simultaneously for 4 seconds.
4. Rotate the cycle selector knob to the 2 O’clock position.
On better model dryers, the error code will appear in the digital display. On good models, the five indicator lights of
Drying, Cool Down, Wrinkle Rid, and Clean Lint Filter Spin will flash the number of times for the first digit of the code
and the START indicator light will flash the number of times for the second digit. Take separate counts of each indicator
light, then repeat to confirm in order to be accurate in identifying the proper error code. The code is obtained by counting
the number of times the lights flash. Example E24: The five indicator lights would flash twice indicating the 2 and the
START indicator light will flash four times indicating the 4. The five indicator lights and the START indicator light start
flashing at the same time. The control will pause for 2 seconds, then repeat the code.
Note: A letter appearing in the code stands for a number higher than nine.
A = 10 B = 11 C = 12 D = 13 E = 14 F = 15
Example Code E4A: the first digit would be 4 and the second digit would be 10. If this code would appear on a dryer in
the Good model line, the five indicator lights would blink four times and the START indicator light would blink ten times.
Troubleshoot problem by using chart below.
To move on to the next code, press the OPTIONS button. To clear code, press the Select button.
To exit this mode, simultaneously press and hold the Select and Pause Cancel buttons for six seconds.

jeff.
__________________
http://www.applianceaid.com/
Appliance Repair Aid
http://www.jrappliance.ca
JRAppliance
3/21/2016 3:12:46 AM • Frigidaire... • Answered on Mar 21, 2016
0helpful
1answer

When I start any cycle, heater works, but few seconds later it stops and beep three times ans status cycle leds on. I said heater works because you can feel a temperature difference inside drum.

Hi Manuel, what I think the problem is with your dryer is there is a thermal overload that has gone bad. The good thing is that it is cheap to fix and you can do it yourself. I could be in and out of your house inside 20 minutes. This is located underneath the top of the dryer and is probably somewhere along the wiring away from the controls.
5/10/2015 12:55:35 AM • Frigidaire... • Answered on May 10, 2015
0helpful
1answer

Dryer won't run just buzzes then displays "pause" with help I can hold the door switch spin the drum and have someone hit the start button and it will run. Do I need a new motor or just a start capaci

will have to check with a meter to confirm either or? normally if ur capacitor is bad u can remove it and shake the unit, if it rattles its bad. other wise do a meter test. If you hear a humming/clicking sound from motor area you more than likely have a bad motor. Try this test out to see if u have weak windings or relay/capacitor on motor. Open the dryer door and turn by hand the drum while machine is on ON position. And you or someone else presses the door engagement switch in. If it starts up then u have bad windings Another thing to check is the belt safety switch. With a multi meter. Especially if u just replaced the belt. The belt safety switch is attached to the Tensioner and motor. IT LOOKS LIKE A DOOR SWITCH SOMEWHAT a little black pc of plastic with 2 prongs going into it. Sits at bottom of motor. Under the Tensioner. Attach meter clips to the 2 prongs on switch, Then when the little white push button is pressed in it should show continuity and none when released. Lastly check ur DOOR SWITCH for continuity with a meter when the button is pushed in the (on/Door closed position,) it may have gone bad. https://www.youtube.com/watch?v=sTRP6kHqAFs
4/22/2015 10:56:34 PM • Frigidaire... • Answered on Apr 22, 2015
0helpful
1answer

My fridgiaire frontload 7000 will not heat

USE MULTIMETER AND CHECK HEATING ELEMENT AND THERMOSTATS, ARE U GETTING A FULL 240 AT THE OUTLET
12/20/2014 6:19:13 PM • Frigidaire... • Answered on Dec 20, 2014
0helpful
1answer

WHAT DOES THE E66 MEAN ON MY AFFINITY DRYER

Good Morning Friend, this is Z, Thank you for your inquiry! An error code E66 is associated with the heating element relay. A technician would typically check the ohm resistance of the relay to determine if it is the cause of the error code on your Frigidaire dryer. If the readings are incorrect, the heating element is replaced. If the readings are incorrect, it could potentially be the main control board. This is not a normal DIY job so you may want to connect with a local servicer to determine the exact diagnosis. I hope this helps explain the error code you are receiving.
5/22/2014 1:23:17 PM • Frigidaire... • Answered on May 22, 2014
0answers
0helpful
1answer

Sudden stop

Do you have an error code displayed ? If so what is that. If not the either the door switch is faulty or the control board. More likely to be the door switch but, strange things do happen.Here is the door switch number 134813601. If you need help installing or more info let me know.
1/30/2014 9:37:52 AM • Frigidaire... • Answered on Jan 30, 2014
0helpful
2answers

Frigidaire Affinity Front Loading Electric Dryer. In about 5 minutes of starting the dryer, an error "Ad" shows in the window above the start button. Then the dryer stops and the lights under the "Ad"

I believe that code means auto dry. Lets make sure the lint and dust is clear from the machine. Check all of your wiring out well since is generally a cause. You may ave to replace the thermistor. Have you gotten any other code along with this.
1/9/2014 12:22:32 PM • Frigidaire... • Answered on Jan 09, 2014
0answers
0answers
0answers
0helpful
1answer

Sqeel sounds like dry bearing in tub

Hi,
Here is a tip that I wrote about dryers and noises...

It will help you determine what is happening there...

Dryer Repair Squeaks, Grinding, Clicking and Knocking Noise


heatman101

Asker's Testimonial "That answer was very informative - thank you fortaking the time to educate me. " - teresa241964
8/14/2011 9:38:39 PM • Frigidaire... • Answered on Aug 14, 2011
Not finding what you are looking for?
Dryers Logo

51 questions posted

Ask a Question

Usually answered in minutes!

Top Frigidaire Dryers Experts

Brad Brown

Level 3 Expert

19187 Answers

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Paul Bade

Level 3 Expert

1818 Answers

Are you a Frigidaire Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Frigidaire Dryers

  • Frigidaire Dryers

Most Popular Question

frigidaire affinity front loading

  • Dryers
Loading...