20 Most Recent Frigidaire FAC126P1 wall/window Air Conditioner - Page 5 Questions & Answers

Standard extention cords are made for light draw applications like lamps and T.V.s. They are not heavy enough for the power that your A/C will draw. You can get an appliance extention cord that is made to handle heavier load such as you A/C. Most hareware stores carry them.

we had this issue inside a warehouse, after carefully watching where the water exited the unit, we used a 3" pvc fitting to collect the water and then reduced it to 1" pvc and ran a drain line to a non-objectionable place. obviously if you are on the tenth story of a building this may not be an option... just an idea :)

Here's the manual...

http://manuals.frigidaire.com/prodinfo_pdf/Edison/220202d019en.pdf

Here's the installation...

http://manuals.frigidaire.com/prodinfo_pdf/Edison/cominstallen.pdf

I spoke with the Frigaire support line 706 374-4432. They said that the large piece of styrofoam, that extends from side to side and nearly top to bottom, is part of the unit. It should not be removed.

It must be installed in a window openeing or through the wall.
A load bearing wall is no problem.
Cutout the opening larger than the unit and install a header in the wall cutout.

If the coils freezes up half-way-down and lower is due to low freon psi.

More than likely this unit could be fixed reasonably. It sounds from your explanation like a bad connection inside the control panel of your unit. Could possibly be what is called a cold soldered joint.

it would appear that you have a fused contactor. If you dont feel comfortable replacing this check on one of the experts on this site. or if you feel ok replacing it remove the case off the old unit. Make sure it is unplugged first. There are two leads coming from the compessor follow these to the block they are connected to this is the contactor you will need to respond with the voltage and amperage rating off of this to size your new one just take the screws loose from both sides of each wire keep track of where they connect to then put the wires in the new contactor the exact opposite of what you rmoved them. Reinstall the cover and you should be good to go

check your name plate voltage and current rating, multiply it and the result is the wattage of the unit.

Check power at outlet.

A humming sound coming from your Frigidaire AC wall unit after it has been powered off could be due to a few different reasons. I can provide some potential explanations and troubleshooting steps to consider:

• FAN MOTOR
• THERMOSTATE DELAY
• ELECTRICAL ISSUE
• REFRIGERANT FLOW
• OTHER MECHANICAL ISSUES

EPTWFU01 is the water filter part number. It isn't the model number of the refrigerator. Please check the model number. Often the model number is on the back of the refrigerator. Not all models support changing the temperature units. If your refrigerator has a button labeled C/F. Try pressing that to toggle back to Fahrenheit. On another model, FG4H2272UF, press and hold the + and - keypads on the refrigerator side of the control panel for 5+ seconds. One Frigidaire Gallery refrigerator is the GLHS36EJSB. The support page is https://support.frigidaire.com/Owner-Center/Product-Support/GLHS36EJSB . The current link to the manual for this model is https://na2.electroluxmedia.com/Original/Electrolux/Electrolux%20Assets/Document/Complete%20Owners%20Guide/English/241856000en.pdf . This model doesn't allow the units to be changed. The documentation for FG4H2272UF is available here: https://support.frigidaire.com/Owner-Center/Product-Support/FG4H2272UF . See the page 15 of the manual, https://na2.electroluxmedia.com/Original/Electrolux/Electrolux%20Assets/Document/Complete%20Owners%20Guide/English/A10883135en.pdf , for the information above. I hope this helps. Please add a comment with your refrigerator's actual model number for specific directions for toggling between degrees C and degrees F. Cindy Wells

This is likely due to a lack of airflow. Make sure that the air filter is clean and that there are no obstructions blocking the air intake or exhaust vents. If this does not resolve the issue, you may need to have a technician come out and inspect the unit for any other potential issues.

Not 100%certain to what styrofoam you are referring to but there is definitely styrofoam components inside the machine. The entire drain pan is made of styrofoam, I would not touch it.

Have you drained the water?

The blower wheel probably is dirty. The unit is sensing that not enough air is flowing across the AC coil.

Mine is doing the same but it's very moldy and dirty. It worked well when we used it for the first month when we moved into our Gma's house. She left the unit. It's old yes but it worked fine before. Why is this happening? I'm going to clean it, but I have NO IDEA HOW TO GET IT OUT OF ITS CASE! HELP

did you clean it with water? They don't mix. Use a hairdryer to dry thoroughly.