Top 20 AEG 24 in. Favorit 50730W Free-standing Dishwasher Questions & Answers

The most likely cause is the interal water heater is not working or if using hot water direclty in the inlet then the water temperature is below rerecommended level.

If this dishwasher is a residential dishwasher the water that is supplied to the unit is from the hot water side of the sink supply. The dishwasher does not heat the water it uses water from the water heater that is connected to the house. It sounds as if the dishwasher is hooked up to the cold water supply instead of the hot water supply. The heating element you see in the dishwasher is for drying purposes and not for heating water. I would check the hot water supply for your dishwasher to see if that could be the problem. Also remember unless you have a recirculating pump on the hot water there will be an amount of water in the pipe from the water heater and the dishwasher that has sat and cooled down over a period of time therefore when you turn on the dishwasher you will not get hot water immediately due to the distance the dishwasher is from the water heater. You will notice when you turn on the hot water to thew sink you do not get hot water right away you let it run for a minute before it gets hot since the dishwasher is connected to the same valve as your hot water to the sink it acts the same way.
Good luck on your repairs hope this helped.

Dave

I don't understand why replies talk about the C2 and C3 errors... The problem is C1! I have the C1 error. I start a programme, it does the draining cycle to check empty then starts filling. MI can hear water entering but it sounds slow at a low flow rate. If I leave it going, eventually the programme stops and the error is displayed: C1 Opening and closing the door allows the programme to continue. I get the error after the various stages of the programme, when it is filling for the next wash or rinse. So it's 4 or 5 times I think during the programme. Now, if I help the filling... When the appliance is filling, I open the door, and poor in a kettle or two of water, then the error does not happen (the fill is within the time expected by the appliance?) So I am thinking one of two things is wrong: 1) I have a flow rate problem BEFORE the water connection to the appliance. E.g. It is blocked somehow. 2) There is something which opens/closes the "tap" within the machine which is causing the flow rate to be low and it does not fill quickly due to that. No idea which of these two, but I did disconnect the hose of the supply and check that water flows quickly from it into a bucket, so I am thinking there is something inside the machine which "opens the tap" and it's not doing a good job of it. Anyone got a clue?

probably the main module ie the pcb you were looking at

http://www.kunnig-elektro.de/reparatur/spuelen/aeg/zulauf2.html

in German ... anyway a couple of pictures :)

The dishwasers have heat (inductive) elements in line with the top sprayer hose and is about +/- 15 cm long and has an electrical push on clip at the side of the device.

Hi i just repaired mine. There was no fuse in it i found the timer control has a tranformer that goes from 240 volt or 115 volt in USA to 12 volts only the on off switch worked .

Question edited for clarity. It is likely to be a control board issue. They are expensive, so call for diagnostics and service. The reason the dishes aren't clean is because it is stuck on wash, so there is no draining and rinses. This machine has some history! https://www.google.com/search?q=aeg+f34300vi0+dishwasher+keeps+running ..

If your AEG FAVORIT 35085 Vi dishwasher beeps five times and stops halfway through a wash cycle, there could be a few potential causes for this issue. One possibility is that there is a problem with the water supply, such as a clogged or partially blocked inlet valve. Another potential issue could be related to the drainage system, such as a clogged filter or a malfunctioning drain pump. It's also worth checking if the dishwasher's spray arms are spinning freely and not obstructed by any debris. If the problem persists, it is recommended to consult the dishwasher's manual or contact AEG's customer support for further assistance. They can provide specific troubleshooting steps and guidance based on your dishwasher's model and any error codes that may be displayed.

If the anti-flood device has activated on your AEG dishwasher, it means that water has leaked into the base of the dishwasher and triggered the safety device. The anti-flood device is designed to prevent water damage to your home and shut off the water supply to the dishwasher. To resolve this issue, you will need to locate the source of the leak and fix it. Here are the steps you can take:

1. Turn off the dishwasher and unplug it from the power outlet.
2. Disconnect the dishwasher from the water supply and move it away from the wall.
3. Check the inlet hose, outlet hose, and drainage hose for any cracks, damage, or loose connections. Tighten any loose connections and replace any damaged hoses.
4. Check the dishwasher door and gasket for any damage or debris that may prevent it from closing properly.
5. Check the dishwasher's interior for any leaks, such as a cracked spray arm or a damaged pump.
6. Once you have fixed the leak, you can reset the anti-flood device by tilting the dishwasher to one side to allow the water to drain out of the base. Then, level the dishwasher and plug it back in.

If you are unable to identify or fix the leak, it is recommended to call a professional technician for assistance.

no info generic answer inlet valve failure --short in valve circuit

Did you check the emergency shut off switch? Almost all under the counter dishwashers have a wall switch to interrupt the power. The problem is it can be shut of on accident.

Look at the screen on the drain.if its clear then check your drain for leaks
As it could be building pressure on the system..by not draining proper.

If you are reading this, then you probably own an AEG dishwasher with a ceiling arm. This part is important for the dishwasher to function properly and needs to be cleaned regularly. However, if it becomes loose or falls off, it can be a real headache to try and reattach it. In this article, we will walk you through the process of how to fix a ceiling arm back onto your dishwasher.

I would check for any bends in anything... a crimp of a wire or bend of a hose can mean the washer will not complete setup and will just refuse like a stubborn mule. If you find no bends or crimps in wires... the brain may be dead. It will be one solid motherboard and should be fairly easy to replace.

possibly a stuck float

Question edited for clarity. Question moved from Washing Machines category. That sounds like a partially broken wire or a control board issue. You need a service call.

USUALLY IN THE WATER PAN

The hose could be clogged or an issue with the valve assembly.Or something being stuck in the inlet water valve. Check to see if there is any problems coming from where the water enters into the tub for your dishwasher mostly on the left side wall of the tub on your dishwasher.