20 Most Recent Bose & Wave& Music System - Page 7 Questions & Answers

If it has a headphone jack have you tried to see if that works ok

had the same problem with the speakers, I am now just using one channel power both speakers, Its not gone on fire yet, not and ideal solution, one channel was driving me mad, and this is free option

Disconnect the power cord in the back. Wait several minutes and then reconnect the power cord. This solved the no sound issue for me.

I replaced the cord.

http://www.fixya.com/support/p167855-bose_acoustimass_15_system/manual-1565/page-10
just click this link

it sounds like the power button has failed. either call Bose to get a RA# and the nearest service center, or find an adventurous electronics tech in your area to replace the switch

you need a 3.5mm male TRS to stereo male RCA plugs. the TRS plug goes in the IPod headphone jack. the RCAs will plug into the line in jacks on the rear of the Wave. good luck.

There are a number of things it could be. The motor, the lens, etc etc. What exactly happens when you put in a CD? No matter what nothing is user serviceable. Go to this page and you should be able to get an estimate from an authorized bose service center. http://www.bose.com/controller?event=VIEW_STATIC_PAGE_EVENT&url=/customer_service/owners/warranty_center/index.jsp
Please take a moment to rate my solution you should find it FixYa! worthy.
Thank you,
Lee

Stations and time are set with the remote as per your user manual.

bose cd will not work but radio is fine

if you are good at opening the player then just follow this steps...
1.take of the screws
2.remove the cover
3.take off the rubber belt connecting the dc motor
4. now you can take the door out by sliding one white coloured clip
5.now clean the obstacles in the door way and every where
use dry clothes..
6.clean the lens also by using the white petrol or spirit....

then reassemble just put the cd and play...
90% it will work
if you are not good at opening then contact the technician........

Did you try resetting it?

If this is the front panel lens for the display, this is a Bose part only. Contact Bose directly to find out how to order the part.

Jerry G.

You should contacty Bose directly to find out about service. There may be a fault in the power supply, or one of the circuit boards in the unit. This will require proper troubleshooting and parts replacements.

Jerry G.

You must contact Bose directly for replacement parts. Most manufacures normaly sell the complete transport as a replacement part.

When changing the laser, or simply removing and re-installing the original, the proper calibration set-up will be required. This cannot be done by eye or ear. This also includes installing a complet new laser assembly.

Jerry G.

Below are some basic instructions of how to clean the laser:
http://www.wikihow.com/Clean-a-CD-Player

If the fault is more involved the unit will have to be serviced, you should contact the manufacture to find out about who in your area can service your player.

Jerry G.

Greetings gaddman43,

Unfortunately your only option might be to deal with the mfg, unless you are handy with electronic repairs. It sounds like you maybe having an issue with possibly several components (i.e. Lens, Drive Motor, Main board) there just arn't any consumer accessories to correct the problems.

You could try a local repair facility that would work on Bose products they should be able to provide basic information on necessary repairs. Even though its an american model the parts should be similar.

Hope this helps.
Jon
Go Ahead. Use Us.

What do you mean drop outs? Like it will play and then stop?

I've repaired about 10 type Bose AWRC3x (the radio/cd model with lift up lid and top controls). If the cd won't play or skips, try cleaning the lens VERY carefully with a cotton bud with some isopropyl alcohol. Let it dry then try again. This will help in about 1/3 of cases.

After that, a new laser unit is needed. They cost around 15 pounds,30 dollars, (Type SFP100s with 13 pin connector made by Sanyo). You need to have some electronics experience to take the case to bits to get the laser deck out, change the cd laser and reassemble. Basically, DISCONNECT THE POWER! Remove the 3 screws on top, turn over and carefully prise the front of the base away from the top cover with a table knife or similar. Lift off the top cover - be careful with the lid ribbon! The deck can be disconnected from its ribbon cable and wired connector very carefully. Take the deck to bits and fit the new laser head (take photos if you think it will help). Remember to unsolder the shorting 'blob' of solder which protects the new laser from static till its fitted.

On the bright side, there is no tracking etc to set up, that's all automatic so usually they work like new with a new laser fitted. I have to say this is the weakest feature on the Bose CD radio, the actual electronics rarely gives trouble.

Hope this helps Steve O'Donnell