Top 20 Pioneer AVIC-D2 DVD Nav/6.5" Screen/AM/FM/CD Player Car Video Player Questions & Answers

The manual does not say anything about changing a language, so perhaps you bring it back to the dealer and ask him to setup the correct language. If you bought it cheap from Japan, I'm afraid not even any dealer can help you, because the rom does not contain any other language.

Hi, i was looking for the same solution and never solved it completely. I was told you can get a cd to convert it however liaison with the company that produce the stereo proved fruitless and they were not able to assist me in getting the cd in NZ to do this. A stereo installer also mentioned knowing someone who did convert these to english in Auckland but they charge hundreds of dollars and i didnt think it was worth it when you can buy a gps unit from The Warehouse in NZ for $100 nz. Good luck, and if you do find a solution that works please do post here to let me know.

Reset the unit and begin with the setup screen to change the language.

ELECTRORAMA ELECTRONICS PH. # 662-6387 TRINIDAD HAVE THE BOOT CD TO FIX IT.. DAVID& DANIEL.

how can i change the language for my pioneer carrozzeria from japanese to english

to access the nav dvd press the open button for a few seconds. then you should be able to eject the old disc and insert the new one.

The Mustang use a 6 volt remote turn on so you need to reduce the voltage by adding 2 resistors. Get two 10ohm resistors and tie the top end together and that will be the out put to the car. The other side will have two wires one is the positive remote from the radio and the other goes to ground. It shouldnt pop then.

-david

la pantalla del Pioneer AVIC-D2. ha perdido la iluminacion

Hi I'm not an expert onthis model but my avic has a memory card slot . For mine to work i need to download a movie on to the card and install the card into the memorycard slot on the avic. Then i go to the main menu screen on my avic and select video option and go from there to watching my movie. Hope this helps . if so leave leave me a posting response . If not you can still get help. Thanks again.

You need to check the power for your camera.The positive at the reverse light works well. Yo0u also need to go in the menu and make sure the avic unit is programed for the camera. And check to make sure you are pluged into the proper port.

contact pioneer at 1-800-746-6337 for a authorized repair facility. I seen this problem on some unit's and needed to send them out for repair. i believe it was a $150 flat rate for repair

sometimes i notice the touch screen calibration is a little bit off...Try to push the okay button a little bit to the left or right working your way from the okay button to the edge of the screen

The brake sensor wire (Lt Green) can be simulated with a toggle switch to ground.
Pink (CAR SPEED SIGNAL INPUT)
The mobile navigation system is connected here to detect the distance
the vehicle travels. Always connect the vehicle’s speed detection
circuit or the ND-PG1 speed pulse generator, sold separately. Failure
to make this connection will increase errors in the location display.
Orange/white
To lighting switch terminal

Light green
Used to detect the ON/OFF status of the parking brake. This lead
must be connected to the power supply side of the parking brake
switch. If this connection is made incorrectly or omitted, certain
functions of your navigation system will be unusable.

Violet/white
(REVERSEGEAR SIGNAL INPUT)
This is connected so that the navigation system can
detect whether the vehicle is moving forwards or
backwards. Connect the violet/white lead to the
lead whose voltage changes when the shift lever is
put in reverse. Unless connected, the sensor may
not detect your vehicle traveling forward/backward
properly, and thus the position of your vehicle
detected by the sensor may be misaligned from the
actual position.
Note: When you use the ND-PG1 speed pulse
generator (sold separately), please make sure
to connect this lead.
When you use a rear view camera, please make
sure to connect this lead. Otherwise you cannot
switch to rear view camera picture.

Further detail can be found here:
http://a248.e.akamai.net/pix.crutchfield.com/Manuals/130/130AVICD2.PDF

bad dvd drive, sorry

I am not sure what you mean by calibrating the touchscreen. If you are talking about adjusting the PCB board for the monitor I can give you a website that will allow you to download a copy of the service manual to show you how to do that. Please let me know.

you either have a faulty cord even though it is charging and/or you may have to do a hard reset of the pioneer by unplugging it from it's power source and the easiest way to do that is disconnecting the battery for 1 min. try the hard reset with the ipod cord plugged in the radio.

the aux inputs will not activate unless you plug an accessory in like a CD changer into the digital input.

i don't know if you know this, but all navi's must be update with the latest software, your system does come with an sd card, take that card an connect it to your computer, and go to pioneer website and download their newest update for your model.

In the navi menu you can choose to avoid highways. as well as choose fastest route. i allways choose th have multipal routs. if that dont work go to the menu and reset radio to factory defaut settings