20 Most Recent Maytag 22.1 cu. ft. Bottom Freezer Refrigerator w / Factory Installed Ice Maker - Page 2 Questions & Answers

It's possible that the issue is with the control board and not just the control panel. Before replacing the control board, here are a few things you can check:

1. Make sure the control panel is properly connected to the control board. Check the connections and make sure they are secure.
2. Check for any damaged wires or connectors. Look for any signs of damage, such as frayed wires or loose connectors.
3. Check the voltage to the control board. Use a multimeter to check the voltage at the control board. If there is no voltage, there may be an issue with the wiring or power supply.
4. Check the fuses on the control board. If the fuses are blown, the control board will not function properly.

If none of these steps resolve the issue, it's possible that the control board is faulty and needs to be replaced. However, it's important to note that diagnosing and repairing electrical issues can be dangerous and should only be attempted by qualified professionals. If you're not comfortable working with electrical components, it's best to seek the help of a certified technician.

Water collecting and freezing on the floor of your freezer compartment is likely due to a clogged or frozen defrost drain. When the refrigerator goes through a defrost cycle, the melted ice and frost should drain through the defrost drain and into the drip pan underneath the refrigerator. However, if the drain is clogged or frozen, the water will collect on the freezer floor and eventually freeze. To fix this issue, you will need to clear the defrost drain. Here are the steps to do so:

1. Unplug the refrigerator to avoid any electrical hazards.
2. Locate the defrost drain at the back of the freezer compartment. It may be covered with ice or debris, so you may need to remove the freezer drawer and any shelves to access it.
3. Clear the drain using a turkey baster or a small funnel to pour hot water down the drain. You can also use a pipe cleaner or a wire to remove any clogs.
4. Once the drain is cleared, you can clean the inside of the freezer with a solution of warm water and baking soda to remove any odors.
5. Finally, plug the refrigerator back in and allow it to cool down before placing the food back in the freezer.

If you're unsure about performing these steps, or if the issue persists after clearing the drain, it's best to consult a professional appliance repair technician to diagnose and fix the problem.

Here you go...watch the video on how to replace the timer... https://www.repairclinic.com/Shop-For-Parts/b4/Maytag-Parts?query=MSD2654FR&searchwithin=defrost%20timer

The crack in the sliding track of your Maytag MSD 2352 ice bucket may be a contributing factor to the ice build up and auger freezing issue. The crack could be allowing moisture to enter and freeze, causing the build up. It is recommended to have the crack repaired or the sliding track replaced to help prevent the ice build up and auger freezing. If you are not comfortable with this repair, it is best to contact a professional technician for assistance.

The issue with your refrigerator turning off and then coming back on could be due to a problem with the control panel or the main control board. Here are a few steps you can try:

1. Check the wiring: If the wiring connecting the control panel and main control board is damaged, it can cause the machine to shut down. Check the wiring and connections for any damage, and repair or replace as necessary.
2. Reset the control board: If the main control board is damaged, it can cause the machine to shut down. You can try to reset the control board by unplugging the machine from the electrical outlet for a few minutes and then plugging it back in. If the issue persists, you may need to replace the control board.
3. Check the thermostat: The thermostat may be damaged or malfunctioning, causing the refrigerator to turn off and then come back on. You can test the thermostat by checking the resistance with a multimeter. If the resistance is not within the manufacturer's specifications, you may need to replace the thermostat.

If you're not comfortable with the above steps, it's best to contact a qualified repair technician for assistance. Also, be sure to confirm the code needed to program the new control panel before installing it.

If your MSS25C4MGZ00 Maytag refrigerator's icemaker is not getting water, here are a few steps you can take to troubleshoot and fix the problem:

1. Check the water supply: Make sure that the water supply valve to the refrigerator is fully open and not restricted. Also, check that the water supply line is not kinked or frozen.
2. Check the water filter: A clogged water filter can restrict the flow of water to the ice maker. Replace the water filter with a new one and check if the icemaker starts working.
3. Check the water inlet valve: The water inlet valve controls the flow of water to the ice maker. If the valve is defective, it may not open to allow water to flow to the ice maker. You can check the valve for continuity with a multimeter, if there is no continuity the valve needs to be replaced.
4. Check the icemaker control module: The icemaker control module controls the operation of the ice maker. If the module is defective, the icemaker will not function. Check the continuity of the module with a multimeter, if there is no continuity the module needs to be replaced.
5. Check the water pressure: Ensure that the water pressure to the refrigerator is between 20-120 psi. If the water pressure is too low, the water valve may not open to allow water to flow to the ice maker.

If you are not comfortable working on your own, it is recommended to contact a qualified technician to diagnose and fix the problem. It is important to note that troubleshooting and repairing a refrigerator can be dangerous, so it's important to follow safety precautions and make sure you are familiar with the appliance before attempting to fix it yourself.

I would remove the track, clean both surfaces and stick it with clear silicone or superglue Gel. Leave it 24 hours to set.

if voltage to compressor then bad compressor it was drawing too much amps thats why the start up capacitor went

Check out the video https://www.google.com/search?q=maytag+refrigerator+model+number+msd2641keu+remove+door+handle ..

Program code is located on the serial plate

Press and hold the Door Alarm keypad.

Press and hold the Freezer Temperature Down keypad within 3 seconds.

Release the door alarm keypad and wait 3 seconds.

The control will display PE to indicate the programming mode.

Press the Freezer Temperature Down once more.

The control will display the current Program Code. This should be the same as the program code on the serial plate. If the code is correct, press the Door Alarm keypad for three seconds to exit.

Press the Refrigerator Temperature Up keypad or Refrigerator Temperature down keypad to change the digit value. The decimal point indicates the selected digit. Press the Freezer Temperature Up keypad to select the next digit. Once the correct program has been entered, press and hold the Freezer Temperature Down keypad until the program code begins flashing indicating it’s been saved. Exit the programming mode by pressing any key.

try running with thermistor unplugged

When your freezer is displaying an SH error code on the temperature display screen, it means that the freezer temperature sensor has shorted out. To troubleshoot this problem, you will need to start by disconnecting your refrigerator from its power source and locating the freezer temperature sensor. Sept 6, 2022

Frigidaire Refrigerator Error Codes Explained

https://paradiseapplianceservice.com > News and Tips Abo

Thanks for your question. https://www.youtube.com/watch?v=3kvs0CPguo4

Thanks for question. I have found your model dimensions Width: 27 1/2 Inch Depth: 27 1/2 Inch Height: 73 Inch Washer Capacity: 7.2 Cu. Ft.

Sounds like the start capacitor has failed. They buzz when the fail and get hot.. https://www.google.com/search?q=maytag+mfi2568aeb+start+capacitor ..

Most used R143a but have changed to Cyclopentane.

Programming Procedure: The replacement control board is not programmed The Refrigerator will not operate without a code selected. It is important to program the control board with the correct code. Product must be powered up to program. If no code has been programmed the display will display 00 or flashing 00. Note: The program code for this refrigerator is located on the serial plate on this unit after the word Code. 1. Open the fresh food door and hold the fresh food door light switch closed while pushing the freezer temperature down key pad 3 times consecutively. 2. Release the Fresh Food door light switch. 3. The control will display PE to confirm entry into the programming mode. 4. Entry is confirmed by pressing the Freezer Down key once more. 5. The control will display no Program Code. 6. To set the desired Program Code number, press the Freezer and Refrigerator UP keys. The corresponding digit will be advanced with each key press. 7. Once the desired Program Code is displayed, press the Freezer DOWN Key until the Program Code begins flashing indicating it has been saved. Note: If you attempt to enter an invalid Program Code the control will not save the code, but will flash Program Code 00, (The unit will NOT run with a Program Code of 00). 8. Once the Program Code has been saved the Programming Mode is exited by closing the Refrigerator door(s). Note: If you to enter a wrong Program Code the control can be reprogrammed by restarting the procedure from the beginning.

The only way is to swap out for a new board unless you are an electronics technician. It looks like defrost is controlled by sensors and a board, that than a timer and heater. Time for a new one. Nearly all parts are becoming obsolete. https://www.partselect.com/Models/MSD2756GEQ/Sections/CONTROLS/?ModelID=137419&ModelNum=MSD2756GEQ&mfgModelNum=&ManufactureID=1&Selected=51963&Position=2&mfg=Maytag&Type=Refrigerator&Mark=2 Slightly better here. https://www.reliableparts.ca/lookup/103151/634799 ..

basic questions you need to ask yourself, is power to unit, is it running is compressor running is condenser fan running. No one can tell you what is wrong without being there.You may need to call for service. The price of food may pay for service call. https://homex.com/ask/how-do-i-reset-my-maytag-mfi2568aes-refrigeratorcopy and paste https://www.ifixit.com/Answers/View/570261/refrigerator+is+not+cooling+Maytag+MFI2568AES