20 Most Recent Hotpoint 24 in. HDA3740G Built-in Dishwasher - Page 2 Questions & Answers

I have same issue, have just worked out that: 1=Intensive 2=Normal 3=Daily 4=Prewash 5=Eco

Check the leak tray inside the base of the machine and see if there is water in there. There is a sensor to detect small leaks.

At 5 months old it should be still under warranty and qualify for free repair...

try just putting it in the bottom of the machine where the water goes

The rear legs may not be adjustable - only the front.

https://searchmanuals.net/search7/?keyword=%2Bowners+%2Bmanuals&gclid=CjwKCAiAqt7jBRAcEiwAof2uKwzE1jBmBNKl9hqWd4TyeToXsj80tGOrdxRc3s6LGEWtoEA-xsOXLBoCIhQQAvD_BwE

I also encountered a similar problem. It was not possible to contact the service center, so I searched for a solution on the Internet, and found it on this site - https://washingcodes.com/blog/#.XFwRwFUzaUk

I once bumped the water supply shut-off under the sink and turned the supply off at the shutoff. Other than that, have you had any work done on the hot water tank recently ?

Hi there, I am from the UK so model numbers vary but all basically the same. Do not fear it is simple really. You need to take the door from it's hinges first. It will either have screws or bolts to the door or frame of the machine. Now you have the door dismantled and in your hands. place upside down and you will see screws ??? they will be situated around the door ?? the door comes in two parts and the glass is sandwiched between the two parts. ( Take photo if in need ) you will see see a metal shaft and spring where your handle will fit. All the best and Happy Christmas from the UK

https://www.google.co.in/search?q=Have+Hotpoint+Dishwasher+model+DF61N+Need+wiring+diagram&rlz=1C1KMOH_enIN790IN790&tbm=isch&source=iu&ictx=1&fir=hfT4fUt27enaFM%253A%252CqTo0BQBDnQ0BcM%252C_&usg=AI4_-kSIDXjWgo94dL3QyAmXQKmlBHCuTQ&sa=X&ved=2ahUKEwiBisX1v_7eAhXDrI8KHfE-AMMQ9QEwAnoECAYQCA&cshid=1543662915079001#imgrc=hfT4fUt27enaFM:

Could be the pump

Soap dispenser issue. Typically this is a control issue. Replace control board.

You need to start by checking the drain and drain pump. This is probably where the problem is.

Pour water in to displace the salt, then drain the machine down

Re. your letter from F.C. about the boyfriend leaving lids off (20 February), I have a similar problem. My husband has developed the habit of leaving all doors, drawers and cupboards open. I don't want to nag, because he gets ratty when I do. I don't think I can scatter insects in all the drawers and cupboards. We are 75 and 79. Any suggestions other than an old people's home?

Are we talking a lot or a little? If the unit is not draining at all then there might be something stuck in the drain pump impellor stopping it from turning at all, or stopping it running as quickly as it should so doesn't drain all the water. Is the drain outlet too high? This can cause the drain pump to struggle to reach the head height, also, water can run back from the drain pipework if blockage or height too high

Sorry have no idea, that is an "O" ring, sure it didn't come off something you washed?