20 Most Recent
Akai PT4298HD Rear Projection Television - Page 4 Questions & Answers
THE COLOR ON THE TV IS STARTING TO GET ORANGE
The picture is formed from three lamps in the base of the TV. These lamps have a fluid filled lens on each of them and the Glycol in this fluid degrades after time. This fluid can also have a mold or algae growing in it.
Check the lamps visually first BUT DON'T touch the driver circuits ( this would be very bad for you) with them turned on and off.
If you need to change the fluid, be very careful as leaks happen very easily. If you get any of this fluid onto the driver board it will damage the tracks etc VERY QUICKLY.
You must replace the fluid with the correct fluid at the correct level and amount and wash your hands afterwards as Glycol is a poison.
I do not think that this is an electronic fault as the orange tinting leads me towards a fluid issue.
My color seems to be more green than should be and
You have a focus/screen control box Find it and adjust the R/G/B screen drives When you first start Go to Menu turn Color off then with a mirror adjust the picture as close as you can to a black and white picture R/G/B screen drives, the little control box you are looking for will have 3 controls on top for focus and 3 controls under them for screen drives to each tube red,green,blue after you have adjusted to a black and white picture then go back and turn color on.
Tv popped and went out
Pops' are never a good thing to hear especially from rear screen sets. Could be that one of the three CRT's went/impolded. Could also be a Capacitor that blew also. Might be best to call a RV repair shop that works on Akai's - I think Magnavox builds Akai's but that's a guess.
Blessings,
A/V Media Guy
RED LIGHT FLASHES 10 TIMES BUT WILL NOT TURN ON!
There might really be a problem with the unit. Try unplugging it out of the power outlet and plug it back in after 30 seconds. If your using a power box (voltage regulator), try plugging it directly to the outlet. If all nothing happens, see a local tv tech in your area. The unit could be damaged.
Where is the ac power supply bar located
Downtown off sixth street. Just kidding. This set has an a/c power supply located outside the wooden frame that secures the main and deflection circuit boards. Very seldom does this cause a problem though. The most common problem in my experience is convergence failure. Testing this is easy. The convergence board is seperate and is mounted above the others. Small pcb with large heatsink. Removing the blue wires with the red plug(I think it's a 5 pin plug) should restore power if set is in shutdown due to that failure. Then you can just try to replace that board if avail. Next problem on this set is coolant can start leaking from the tubes and go onto the circuit boards. Use a bright light and a good pair of eyes to examine the board closely, looking beneath the picture tubes for moisture or drops or corrosion on boards. Please make sure tv is disconnected from power source while testing and good luck, Russmann.
Where is ac power supply board located?
GO THROUGH TRACING THE MAIN CORD, IT WILL LEAD YOU TO MAIN BOARD, MOST PROJECTION TV HAVE 2 OR MORE BOARDS.....IF YOU ARE ABLE TO SEE BIG CAPACITORS HAVING 400V OR MORE VALUE, THATS THE ONE..CHECK OUT..
SHOWING DOUBLES
You have a
convergence board out of adjustment or faulty the best way to tell this is to have a estimate done on it but I can tell you its a convergence issue that is not fix can get worse over time.
This is nothing we can fix over email but we can give you paid advice and that is have it looked at locally as this is a complex issue that cannot be fixed over a email system.
Please do click the ACCEPT BUTTON to accept my advice.
Thanks
Rulds2008
Expert Tv repair Guru Btw, I’m available to help over the phone in case u need at
https://www.6ya.com/expert/edwy_1a56970cf1ea4620
Red and green projection is separated
Hi,
It still can be fix, the unit need an immediate repair, a problem on the video output module has something to do with this, a burnt resistor or capacitor has to be replaced.
Hope this info helps
Akai pt4299hd
Try recycling the power, Unplugg the power cord wait at least 2 mins ant then plug back in. Some times by turning it off an on rapidly will cause the microprocessor to lock up or freeze. Much like a computer does when you have to reboot it..
Akai pt4298hd
Look at AC power supply board they are bad about poor solder joints resolder thyrisitor on board.
Not finding what you are looking for?