20 Most Recent Hotpoint RVM1635 Microwave Oven - Page 9 Questions & Answers

Your probably hearing just the fan. If the primary part, (the magnatron), is bad you'll get no heating. With the cost of microwaves dropping dramatically you may be better off buying a new one, rather than replaceing the magnatron.
BTW, replacing the magnatron is not a DIY job.

Hi,
It just means that it is "on" it has power and is working..that's it...

heatman101

This web site shows you the pilot adjustment acrew on a typical gas oven:
http://home.howstuffworks.com/how-to-repair-an-oven6.htm
Go to this site and select your full model number and you will get a neat page that has the diagrams and parts lists for your model, should you need them:
http://www.appliancepartspros.com/partsearch/modelsearch.aspx?model=RGB524
Hopefully, it's just an adjustment.
Good luck, thanks for using FixYa, and hope this helps.

Somehow in the process of selecting the language, the new selection isn't being "set", and that's usually by hitting some button to change it permanently. Refer to the manual and review your steps. It's entirely possible that the manual is erroneous, and an extra button will have to be pushed to seal it.
I found this blog on manualsonline.com:
i cannot change the language on my hotpoint i've tried everything in the manual any ideas

Add a comment | Get notified about comments

Comments

• Same problem here
  When moving the machine into the house the language was accidentally changed to something I can only guess is Czech. Does anyone know how to reset the machine or change the language back to English?
  
  Many many thanks.
  -->Was this comment useful? new Starbox("rating4049513", 4.0, {identity: 4049513, stars: 5, buttons: 5, max: 5, total: 1, onRate: saveVote});
  
• RE: language problems
  You need to press the bottons stated on the manaual for a few good seconds until it beeps. Once it beeps will turn off, once you turn it back on you can then change the language to English again.

Perhaps that will help.
Anyway, good luck, thanks for using FixYa, and hope this helps.

You can download GE owner's manuals and installation instructions here.

We're happy to help you with free advice and we'd appreciate your thoughtful rating of our answer.

Sorry, but that's not a proper Hotpoint/GE model number.

Please note that FixYa is not currently notifying us Experts when Clarification Requests are answered.

To allow us to help you effectively (at no charge), please post a NEW problem to FixYa, and please include your brand name and the full model number from the tag in or on the unit, and your detailed symptoms.

This is usually caused by either a bad door switch or a loose door switch mount, which are pretty simple problems to fix.

Door switch or mount trouble is usually caused by slamming the door or by opening the door while it's cooking without hitting the Stop pad first.

There are plastic mounts inside the microwave which hold the door switches and onto which the door latches lock when you close the door.

The screws on these mounts may be loose. If they get too loose, the switches will not be activated properly.

Sometimes it's a broken tab on the switch holder, allowing the switch to rotate just out of position. This tab can be hard to see, since it is under the bottom edge of the switch.

If the switch mount is broken, it's usually more economical and safer to add a dab or two of hot glue to the mount to secure the switch. Let it cool for about 30 minutes before using.

One test that sometimes helps is to gently lift up (and/or push down) on the door or handle as you try to start it. If it works or tries to work, then it's a door switch mount or door alignment issue.

You can find links to helpful exploded view diagrams and part ordering help here.

I recommend that you bookmark that link to your favorites.

There should be a "mini-manual" (tech sheet) hidden inside the unit behind the control panel or hidden on the left side behind the grille, which is very helpful when troubleshooting, testing, and locating components.



At our Web site, we have a video available showing how to remove a typical over the range control panel assembly in under 5 minutes.

You can also see the following links:
http://www.microwavedisplay.com/safety.txt
http://www.microwavedisplay.com/disassembly.txt
http://www.microwavedisplay.com/doorsw.txt

If you only need a switch, you can order a universal type here for $5 postpaid.

We're happy to help you with free advice and we'd appreciate your thoughtful rating of our answer.

there is no reset button on a microwave. what is the exact problem please?

this sounds like your megertron has burnt out,, best bet is bin it and buy a new one there only £50.00p up now, to fix yours will cost all of that, and dont try fixing it yourself it can kill you, there could well be over 1000 volts inside your unit, tuch that and its a set of wings for you, ok!

HI. The most common issue here will be a failed turn table motor. This motor is located beneath the actual table housing. replace this failed motor.

Note(The uncommon problem area will be a failed relay. although, highly uncommon, this may be the issue. i would advise to inspect the motor control relay located on the main control-board for visible burn marks)

Check your door satey interlock switches.

If these switches fail (do you open the door while the machine is cooking?), the microwave doesnt know the door is shut and will not turn on the magnatron.

If you need more help, let me know.

a

They may not be fixable, depending on the type of buttons used. Many devices use a 'snap dome' switch, which is a little metal disk that 'pops' in and out like an oil can. Problem is, sometimes they get pushed too hard, or just get old, and they stay in the 'popped' position. It is sometimes possible to repair them, often not. A repairman is likely to charge more than the cost of a new one: they'd have to take the thing pretty much apart to get to it, and then may not be able to fix it.

Sorry it's not much help.

You can buy the glass from

http://www.us1internet.net/RVM1325BW02/

You can also try partstore.com

Please make sure to rate this solution

F3 on a GE / Hotpoint microwave means you have a shorted membrane keypad.

So until it is repaired, please leave it unplugged or leave the door open when it's not in use, and please do not leave it running unattended.

On this model, the membrane keypad is not available as a separate part, so you would have to order the control panel frame assembly, which comes with a new keypad.

At our Web site, we have a video available showing how to remove a typical over the range control panel assembly in under 5 minutes.

Then you disconnect the keypad strip as shown in the attached photo.

Next, move your circuit board into the new frame. That is a simple do-it-yourself job.

You can find helpful exploded view diagrams and order parts by entering your full model number here.

The control panel frame assembly with keypad is part number WB07X10874 and you can get it for $75.98 here. (Compare that to $120.75 from GE!)

We're happy to help you with free advice and we'd appreciate your thoughtful rating of our answer.

It is very likely that the motor that spins the plate is wearing out. You can find a replacement on ebay and many other sites.

Many thing can do this but, common things are....loose high voltage wire.....poor solder joint on board.....magnetron.....power relay.....