Top 20 E-Machines T6520 PC Desktop - Page 3 Questions & Answers

the PCI simple comm controller is part of the chip set drivers. You can find these at E-Machine's website, under support. Since you did not provide a model number I can not be more specific than that.

When the computer first boots up, it will go through the POST. Which is power-on-self-test. Right after this press F1 to get into the BIOS. BIOS is Basic-Input-Output-System. Inside the BIOS you can configure your boot options. You can move the priority of the CD ROM or USB to the top, above the hard drive. (I'm guessing the Operating System is inoperable.) You can now save and exit. insert a windows disc, to repair or format the hard drive and reinstall the operating system. I recommend though trying Ubuntu. visit ubuntu.com for install instructions.

firstly lets think why a Working pc would no longer BOOT. The boot process then. a pc starts the bios which POST's. this results in ONE BEEP which might be followed by messages(if you get several beeps then they are like morse code long/short and count out an error code). when you get your ONE BEEP the pc is working. when it then HANGS(appears to do nothing) its usually because of either a) the cd drive is duff so disconnect its cables. b) the hard drive is duff so disconnect its cables c) the hard drive hasnt quite died yet but has some very slow sectors and is making the Clackety Clack of the heads recalibrating every few seconds. d) there could be a a gpu card bios glitch and your pc is running but you just have a blank screen. some hints then 1) never start removing parts as that corrupts the CMOS(the battery backed up configuration for your BIOS) so you may need to clear your cmos. 2) never play with the idea of changing ram sticks as people usually end up putting them in any old slot(which may result in a non working pc). make sure a PAIR is fitted in slots 0/2 and a separate matching pair in 1/3 slots not in slots 0/1 which is two half pairs. Other factors. 1) a short circuit. your PSU has built in protection, if the psu fan(inside case of the psu) turns and kicks back and immediately stops you have a short circuit and its cuts the power to avoid a fire/meltdown, which could be caused by high wattage gpu(>60 watts) without its extra power cables fitted or wrongly connected front usb cables or removing a mainboard and fitting it into a new box where the board has its support posts NOT lined up with the holes fro the screws so the post is touching underside of the board circuits. hope some of that helps.

to boot a cd then you must have the bios set to allow it, or tap f12 immediately to intercept boot menu and choose cd. sounds like your drive has a few bad disk sectors.

Download a Linux distro to a flash drive or DVD and see how well it runs off that. There's HDD utilities like SuperGrubDisk that can diagnose things.

the monitor is dead. PSU dead inside. only used PSU sold on ebay.

well that is 17,000 volts there 17kv and can be lethal . CRT is cathode ray tube and 2nd anode is 17kv, 1kv per inch screen.. we use a chicken stick to discharge that. one guy gut hit here and flew across the room ,hit head and next up paramedics deep.. not fun to see that. ive taking 600v but never again. vaccum seal, why do that.??? send it to the , toxic lead recycle center, let them do the danger work when I was only 16yo I worked in TV shop and I had do that "nnipp" that in the bud on all CRT sent off to refurb. (or toxic trash) (we sold them all here, you name it) we had to remove the socket there find he glass bud there dead center and full PPE, and snap it with wire cutters and it sucks in air fast. later in military too on old radar scopes, i worked . the vacuum inside is pure and prefect, zero gasses. implosion hazard exists. a glass flies in the bounces out and hits you and then next up blind i one eye. leave CRT alone to the trained.

Unfortunately, without a specific model number for your monitor, this may vary from the manual I am referencing. Just the same, I should say the link should at least have enough similarities to get you out of a scenario mode, and into the custom configurations (that I am assuming you are after). The steps begin on the bottom of page 5. http://global-download.gateway.com/GDFiles/Document/User%20Manual/User%20Manual_Acer_1.0_A_A.zip?acerid=634321354437313817&Step1=MONITOR&Step2=FLAT%20PANEL&Step3=E182HL&OS=ALL&LC=en&BC=EMACHINES&SC=PA_6E If you are using a similar model, clicking on the menu button will bring you in the OSD menu where you can customize the brightness, contrast, etc. Any changes will become a "custom" mode that will effectively take you out of anyone of the scenario modes. I have seen monitors that do not allow much customization (if any) outside of the scenario modes. You may find specifics if you search the monitor model number itself. If you post that information in the comments I can help you find info more specific to your display.

Knowing the beep pattern will help diagnose the issue. Power on the computer again and listen for long beeps and/or short beeps. There are other possibilities, but if you just cleaned out the computer, I suspect you might have dislodged a memory stick. Make sure they are seated completely and the white tabs are locked securely in place. The beep code you hear will ultimately help determine where the failure is happening.

try booting to safe mode. by using f8if that works, try a system restore to a previous date. if that does not help, then it must be a windows corruption and parallel install or repair install will be needed, it can also be fixed by manual troubleshooting and repairing the files.

it depends if it a pc or laptop you can HBCD 15 OR HIGHER TO CLEAR THE PASSWORD. IF IT IS A CMOS PASSWORD YOU CAN TRY TO CLEAR IT BY TAKING OUT THE CMOS BATTERY AFTER YOU UNPLUG THE COMPUTER OR BY USING THE JUMPER TO CLEAR IT (SOME, BUT NOT ALL). How to Clear Your Computers CMOS to Reset BIOS Settings How to Reset Your Forgotten Windows Password the Easy Way http://www.wikihow.com/Delete-Someone's-Windows-Password

"Stumble" is not an appropiate computer term. I don't understand what do tyou mean by getting or not a picture when you stumble

Hi, Can you post any other details about the device you are using, the operating system, that sort of thing? Was there any other error message on the display? I post on behalf of HP.

Sounds like there was a surge when you plugged in the charger, and it fried the system. Chances are the data is recoverable if you remove the hard drive and install it in a different computer, but to me it sounds like that machine is dead.

The beeping sound is the POST, pre-operating system test trying to tell you what is wrong. Unfortunately there is no manual available for this motherboard. The chipset has a manual, but not a list of the POST beeps. here. http://www.go-gddq.com/down/2011-08/11082014121091.pdf You can contact gateway support here. Contact Support

To delete your Facebook account, you can refer to the guidelines mentioned on the following link: http://www.fixya.com/support/t24961110-delete_facebook_account GuruAid.com

Probably all it needs is the proper driver. You should have gotten several disks with the laptop containing OS, drivers, etc. If not, go to the Acer's site and download the proper drivers and install them. They will have installation instructions posted or for download. Unfortunately, I can't tell you who manufactured the webcam in your PC. Should be available on Acer's website. I do find it odd that Win 7 doesn't have the drivers already installed tho. Most major webcams are covered, especially if you bought the laptop with Win 7 installed. Can also try going to device manager and uninstalling the webcam, then reboot. Windows will reinstall the webcam. Try updating the driver from device manager also.

Take it back and get a refund or password from the supplier as "it is not fit for purpose".

Sounds like it's overheating. A lot of times the processor's thermal paste has been burned up or the fan isn't spinning. Computers have built-in temperature gauges that will act as kill-switches in the event of the temperature heating up too much.

Need more information here explain briefly