Top 20
Jet Tech Systems CHALLENGER Dishwasher - Page 6 Questions & Answers
Hobart Commercial Dishwasher - I have an error 015 Failure pressure sensor booster. No technicians available for a week! Help!
Error 015 on a Hobart commercial dishwasher indicates a failure of the pressure sensor in the booster. This can cause the dishwasher to stop working or not function properly. Here are some things you can try to troubleshoot the issue:
- Check the connections: Make sure the connections to the pressure sensor and the booster are secure and not loose.
- Clean the sensor: Clean the pressure sensor and the booster with a damp cloth to ensure there is no debris blocking the sensor.
- Check the water flow: Make sure that the water flow to the booster is not restricted or blocked.
- Check the water pressure: Make sure the water pressure is within the specified range for the dishwasher.
- Check the control board: Make sure that the control board is not damaged or malfunctioning.
- Check the wiring: Make sure that the wiring of the pressure sensor and the booster are not damaged or disconnected.
If none of the above steps resolves the problem, it's recommended to wait for a technician to come and fix it as the pressure sensor is a critical component and if not fixed properly it could lead to further damage. However, you can try to contact the manufacturer and ask if they have any troubleshooting advice or if they can send a technician earlier.
1/16/2023 10:28:32 PM •
Dishwashers
•
513 views • 0 helpful votes
On my power probe I'm getting an error code. C8 does anyone know what this means? And how do I fix it?
The C8 error code on a Power Probe is typically associated with a problem with the temperature sensor. This code is indicating that the temperature sensor is detecting a temperature that is out of range or is malfunctioning.
Here are a few things you can check to fix the C8 error code:
- Check the temperature sensor: Make sure that the temperature sensor is properly connected and that it is not damaged.
- Check the wiring: Make sure that the wiring between the temperature sensor and the control board is not damaged or loose.
- Check the power supply: Make sure that the power supply is providing the correct voltage and that it is not damaged.
- Check the control board: Make sure that the control board is not damaged or malfunctioning.
- Clean the temperature sensor: Clean the temperature sensor with a soft brush and make sure it is not covered with debris
1/10/2023 7:03:38 PM •
Dishwashers
•
548 views • 0 helpful votes
Hisense Dishwasher E3 error
Error message E3 in integrated compact dishwasher indicates too much inlet water and/or a leak.
12/8/2022 9:49:13 AM •
Dishwashers
•
1,290 views • 0 helpful votes
Klarstein Dishwasher (Amazonia) when turned ON display cycles through the options, and buttons are unresponsive
If your Klarstein dishwasher is cycling through the display options and buttons are unresponsive, it is possible that there is an issue with the control board. Here are a few steps you can take to try and resolve the issue:
- Unplug the dishwasher from the power source for at least 5 minutes, then plug it back in and see if the issue persists.
- Check the dishwasher's circuit breaker or fuse box to make sure that power is being supplied to the unit.
- Inspect the control board for any visible signs of damage, such as burn marks or corrosion. If you find any damage, the control board may need to be replaced.
- If you are comfortable working with electronics, you can try resetting the control board by unplugging the dishwasher, removing the control board, and disconnecting the ribbon cables. Leave everything disconnected for a few minutes, then reassemble and reconnect everything.
If none of these steps resolve the issue, it may be necessary to contact a professional appliance repair service for further assistance.
3/18/2023 5:58:33 PM •
Dishwashers
•
62 views • 0 helpful votes
New Bellini dishwasher- No water source error- using for the first time ever
It sounds like there may be an issue with the installation or water supply to the dishwasher. Here are a few things you can try to troubleshoot the problem:
- Check the water supply: Make sure that the water supply valve is fully open and that there is adequate water pressure. Also, check that the water supply hose is properly connected to the dishwasher and to the water supply valve.
- Check the water inlet valve: The water inlet valve is responsible for controlling the flow of water into the dishwasher. Make sure that the valve is fully open and that there are no kinks or blockages in the hose.
- Check the float switch: The float switch is a safety device that prevents the dishwasher from filling with water if the dishwasher is already full. Make sure that the float switch is not stuck or malfunctioning.
- Check the drain hose: Make sure the drain hose is properly installed and not clogged.
- Check for leaks: Make sure that there are no leaks in the water supply hose, the inlet valve, or the drain hose.
- Contact the manufacturer: If you have tried all of the above steps and are still unable to fix the issue, contact the manufacturer for further assistance. They will be able to provide you with additional troubleshooting steps or advice, or they may need to send a technician to repair or replace the dishwasher.
It's important to note that if the dishwasher was not installed for 2.5 years, it is possible that some components may have become damaged or malfunctioned due to lack of use, and you should contact the manufacturer or a professional service technician for further diagnosis and repair.
1/9/2023 12:30:07 AM •
Dishwashers
•
245 views • 0 helpful votes
Ariston dishwasher LFB 5B010 EX on/off, rinse aid and salt lights are flashing, left washing light orange and green (end) light on without flashing.
It sounds like there may be a problem with your Ariston dishwasher. The flashing lights and the dishwasher's inability to wash could be caused by a number of issues, including a problem with the control panel, a faulty water inlet valve, or a clogged wash pump.
To troubleshoot the issue, you can try the following steps:
- Check the control panel for any loose or damaged wires. If you find any loose or damaged wires, try to secure them or repair them as needed.
- Check the water inlet valve to make sure it is not clogged or faulty. The water inlet valve controls the flow of water into the dishwasher. If it is clogged or faulty, it could cause the dishwasher to stop working.
- Check the wash pump for any blockages. The wash pump is responsible for circulating the water during the wash cycle. If it is clogged, it could prevent the dishwasher from washing properly.
1/2/2023 3:30:59 PM •
Dishwashers
•
237 views • 0 helpful votes
Swan dishwasher not working
If you have checked the power supply and it is not the issue, it is possible that the control board or other internal components of the dishwasher may have malfunctioned. Here are a few things you can try:
- Check the dishwasher's door latch to ensure that it is closed properly. If the latch is not engaged, the dishwasher will not start.
- Check the dishwasher's circuit breaker to see if it has tripped. If it has, reset the breaker and try starting the dishwasher again.
- Make sure the dishwasher's control panel is not locked. Some models have a control lock that can be activated by pressing and holding a certain button or combination of buttons. If the control panel is locked, the dishwasher will not start.
If none of these steps help, it may be best to contact a professional appliance repair technician to diagnose and repair the issue.
2/1/2023 5:30:13 PM •
Dishwashers
•
90 views • 0 helpful votes
I put the rinse aid, but it does not show on the indicator that there is rinse aid
Please try these steps.
- Open the door completely and remove the rinse aid cap by turning it counterclockwise.
- Add the liquid rinse aid into the dispenser (until the rinse aid level reaches the full mark.)
- Close the rinse aid cap by rotating it clockwise.
- Set the rinse aid indicator dial to a number between 1 and 6. ...
- Replace the cover.
12/8/2022 2:19:36 AM •
Dishwashers
•
387 views • 0 helpful votes
Hi my dishwasher top rack closes until it reaches the spray connection then stops unless you wiggle it about then closes it seems too low any advice would be great
If your dishwasher top rack is not closing properly and is stopping when it reaches the spray connection, there are a few things you can try to fix the issue:
- Check the Spray Arm: Make sure the spray arm is not blocked by any dishes or debris. Clean it if necessary.
- Check the Spray Tower: Ensure the spray tower is properly seated in the dishwasher and not blocking the top rack from closing.
- Check the Rack Adjusters: Make sure the rack adjusters are properly positioned and adjusted to fit the dishes in the top rack.
- Check the Rack Rollers: Check that all the rollers are present, functioning and not damaged. If any of them are missing, damaged or not functioning, you should replace the rollers.
- Check the Track: Make sure the track the top rack rides on is clean and free of debris.
- Check the dishwasher's leveling: Make sure the dishwasher is level. If it's not level, it can cause the top rack to not close properly.
If the problem persists, it may be an issue with the dishwasher's design or a malfunctioning part that may require a professional to fix. It is best to contact the manufacturer or a qualified technician for further assistance.
It's important to note that the above steps is a general guide, and specific instructions may vary depending on the model of your dishwasher.
Hope this helps!
1/17/2023 10:50:50 AM •
Dishwashers
•
126 views • 0 helpful votes
Not finding what you are looking for?