Top 20 Jet Tech Systems CHALLENGER Dishwasher Questions & Answers


Be sure you don't have "economy mode" turned on.

Jet Tech Systems... | 72 views | 0 helpful votes


for models equipped with a drain pump;
verify that the pump is not clogged. if it hums during the fill cycle or rinse cycle then something is lodged inside. If it doesn't then it needs to be replaced.
for models without the drain pump;
something is interfering with the water flow. when the stand pipe is removed, the tank should empty in about one minute.

Jet Tech Systems... | 206 views | 0 helpful votes


The detergent system on the Jet-Tech machine are all very similar. Near the solenoid valve under the machine, beside the drain connection, there are two wires, one red and one blue. Those wire will run the detergent pump when the machine calls for water. Two tube are attached to the pump. when looking at the pump from the front or clear plastic can be seen, the tube on the left (arrow going up) is connected to the container with the detergent. the tube on the right (arrow down) is connected to the back of the unit to inject the detergent into the tank. Some precaution should be taken to assure that the connections are tight and not leaking. if the tube shows signs of crystals inside, it should be replaced as the detergent as crystallized within. Search by part number or description

Jet Tech Systems... | 76 views | 0 helpful votes


On the F-14, the booster thermostat must be satisfied. The rinse thermostat must work properly and or the rinse heater. follow the diagram. This kind of troubleshooting is done by qualified technician. Remember to unplug the unit before opening the panels. It could be just a burnt wire on the rinse booster heater connection.
. 39986f38-1a20-4562-92ba-c0c84a39bf50.jpg

Jet Tech Systems... | 61 views | 0 helpful votes


Most Jet-Tech dishwashers has one adjustable rinse thermostat and one fixed wash thermostat. The wash thermostat can be substituted with an adjustable thermostat. Location depends on the model. F-18 are located on top. F-22 are located under next to the wash tank. Search by part number or description

Jet Tech Systems... | 151 views | 0 helpful votes


a plug can be warm. if it is hot to the touch, stop using it and have the machine checked and the receptacle check by a qualified technician.

Jet Tech Systems... | 42 views | 0 helpful votes


If the machine will fill on its own when it is empty then the rinse cam on the timer is defective

Jet Tech Systems... | 121 views | 0 helpful votes


No idea as i would either make my own or go to general store in alicante and ask the nice man if he has anything that would do the job if the original parts were not available

Jet Tech Systems... | 209 views | 0 helpful votes


www.jet-tech.com/products/F-18DP/f18_tech_manual.pdf

Copy and paste that link into your internet address bar or type it in.
That is your manual

Jet Tech Systems... | 375 views | 0 helpful votes



Hi,

That is not that hard to fix and you can easily buy the parts yourself online...

Here is a tip that will help you with the online buying...

How to Buy Appliance Parts Online

heatman101

Jet Tech Systems... | 132 views | 0 helpful votes


If this is a common problem then ring the manufacturer, if not you will need to have it replaced.

Jet Tech Systems... | 66 views | 0 helpful votes


There is an adjustment for that OR the unit got snagged when it was installed. You need to remove it from under the counter a little and see if it opens all the way. There are pulleys, springs etc near the bottom of the door that adjust that tension. Make sure they are not caught on the cabinets etc.

Dishwashers | 38 views | 0 helpful votes


AND WHAT COULD POSSIBLY BE THE FIX . A NEW GASKET , WE DO NOT KNOW IF THAT IS AVAILABLE ANY MORE , A NEW MACHINE MIGHT BE THE ONLY RECOURSE FOR YOU

Dishwashers | 49 views | 1 helpful votes


A failing inlet water solenoid valve. You need a new one.

Dishwashers | 33 views | 0 helpful votes


Check the start capacitor also. The rating of the capacitor will be written on it. Likely to be anywhere from 5uf to 15 uf. If the cap has failed, it wont start the pump properly. If you are having a voltage supply fault, its possible the board has failed.

Dishwashers | 67 views | 1 helpful votes


You will need some skill with tools and knowledge of how your dishwasher operates. First, you will need to remove the back or front panel on the door. This will depend on the kind of dishwasher you have. When opened, look for a metal or plastic arm coming from the dispenser to a motor or gear. This is usually the problem and can be purchased from this site.

Dishwashers | 38 views | 0 helpful votes


Hi,
That is a water inlet fault. If the tap under the sink is turned on and everything else seems OK then the inlet hose/valve will need to be replaced by a technician

Dishwashers | 55 views | 1 helpful votes

Not finding what you are looking for?
Jet Tech Systems CHALLENGER Dishwasher Logo

Popular Tags

1 questions posted

Ask a Question

Usually answered in minutes!

Top Jet Tech Systems Dishwashers Experts

Robert Marsolais
Robert Marsolais

Level 1 Expert

12 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Brad Brown

Level 3 Expert

18060 Answers

Are you a Jet Tech Systems Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Jet Tech Systems Dishwashers

  • Jet Tech Systems Dishwashers

Most Popular Question

dishwasher not dry

  • Dishwashers
Loading...