20 Most Recent Yamaha HTR-5990 Receiver - Page 2 Questions & Answers

Page 88 in the Manual:

Under ADVANCED SETUP

1. Press Master On/Off to set the unit to the standby mode.

2. Press and hold STRAIGHT / EFECT on the front panel; and then press Master On/Off inward to the ON position to turn on the power to this unit.

3. Rotate the PROGRAM selector on the front panel to select the parameter you want to adjust.

The name of the selected parameter appears in the front panel display.

4. Rotate the PROGRAM selector on the front panel repeatedly to change the setting.

5. s Master On/Off on the front panel to release it toward the Off position to save the new settigns and set the unit to standby mode.

THIS is the parameter you want to find in the procedure above:

"PRESET"

Use to reset all the parameters of this unit to the initial factory settings with the exception of System Memory and AUTO SETUP settings.
Choices: CANCEL, RESET
* Select CANCEL if you do not want to reset the parameters of this unit.
* Select RESET to reset the parameters of this unit.

The RVA350 comes with this model according to the manual.

Hope this helps

check the power to the speakers by meter it must be getting overheated. the speaker wires are either not connected properly or the speaker amp ic is getting overheated.get it checked with a meter to confirm the fault. Check out.keep updated.thanks.

You probably need to take that issue up with the setup of the unnamed device originating the signal.

YAMAHA HTR-5990 FACTORY PRESET PROCEDURES
All models require the STANDBY/ON button to be turned OFF to start the reset process.

NOTE: The remote control cannot be used during the reset procedure. All necessary buttons to complete the reset process are located on the front panel of the receiver. This procedure is not intended to correct intermittent shut-off symptoms or problems

MODEL: HTR-5990 (U.S.A. model/s)
(BEFORE YOU CONTINUE, PLEASE READ THE ABOVE NOTES!)

1. Before you start this procedure, locate the MASTER ON/OFF button and the STRAIGHT/EFFECT button on the Front Panel of the unit.
2. MAKE SURE THAT YOUR RECEIVER'S MASTER ON/OFF HAS BEEN TURNED OFF.
3. With the Right Hand, press and hold the STRAIGHT/EFFECT button.
With the Left Hand, press the MASTER ON/OFF button and HOLD both buttons for no more than 3 SECONDS, AT THE SAME TIME.
SP IMP. * 8 MIN. will appear on the display, which indicates you are in the Diagnostics Mode.
4. Rotate the PROGRAM KNOB to the right (ONCE) until the display reads PRESET *CANCEL.
5. Press the STRAIGHT/EFFECT button (ONCE) and the display will change to PRESET RESET.
6. Turn the unit off by pressing the MASTER ON/OFF button.
7. Wait 5 seconds, then turn the unit on by pressing the MASTER ON/OFF button. You have now reset your component to the factory settings.

NOTE: Yamaha receivers don't have to be reset during normal operation. It is not recommended that you reset the receiver unless a setting has been changed that you are not aware of, or the receiver is not operating properly. The reset procedure will clear an incorrect setting that might be causing abnormal operation.

Hope help with this.

Is it going into protect mode???
If so, check your speaker connections. Make sure there are no loose copper wires hanging out, and that your splices are clean at both the receiver and the speaker.

Most likelly you having problem with signal cable. Sounds like, ground conductor inside of your signal cable is broken. Try to replace the cable.

The receiver is in "Setup" mode and wants the microphone plugged in for testing sound parameters. Press "menu" on the remote, this will exit the mode. If you still have an issue, post a comment and I can help you some more.

unplug everything that is pluged into the reciever. plug the power cord into an outlet with nothing else pluged into it and try it again. if your electronically experienced you could try to ground it and carefully try it again. give the unit a smell, does it smell a little burnt? if you have a screw driver and a little trust in yourself tale the cover off and look at the board for visual burn marks there should be fuses inside the unit, you could check those out. If you dont see anything visually wrong and it is still not powering it would be a good idea to bring it in to an electronics repair shop and they could diagnose the problem. With the use of a volt ohm meter it would not take long.

Try turning off any surround mode so all you have working is the 2 front speakers. If the soundgoes away, the problem is in the digital surround processing and you are hearing the results of digital noise. Since this unit is new, return it for an exchange indicating the problem. It should not be making this sound.

Dan

MichaelM
Did you ever get this resolved?  I have a similar problem, my video feed seems to work but I have never been able to get any sound from my speakers using this component.  I'm not sure what YPAO setup is but I just read a suggestion to reset the receiver to factory settings in the event something is programmed that causes the problem.

The unit is most likely getting too hot. Check your speaker cables for frayed wires that may be touching each other. The amp will continue to work, but work much harder into a lower impedence load. Over time this will damage the amp. If the cables are OK, try running the amp with the speaker wires disconnected. If the unit still behaves the same way, there is a problem internally with the output section that should be corrected ASAP.
Dan

Hey Kris, this might all be about different 1080 settings. Maybe Your consoles work on 1080i and the TV is 1080p.
It more sounds like your receiver has a faulty HDMI jumper, which you wont be able to fix. Here`s what i would do:
If your lcd has two HDMI inputs, use on for each the receiver and the other for the ps3...
2-For how important is to rather connect the ps3 via HDMI, for picture quality. then simply get an HDMI splitter, yes... YOull have to go and switch from receiver to ps3 whenever you want to play BUT it really sims your receiver is not going to cut it.

The pink you see is an incorrect "GAMMA" signal thats only induced by a malfunctioning software or hardware.

Is your receiver from a cable company? Try to get it replaced.

I would start there and if it wont make a difference, go with the splitter. YOu might get one at walmart, Radio Shack or ebay.

Hope it works and please feedback with results.

Good luck!!!

Jean

Sorry Michael, you have a problem in the audio amp section of the receiver and unless you know how to troubleshoot solid state electronics, you will need to have this unit serviced by a pro. Good Luck

if you are useing component cable on you dvd, and you dont get video ! Check your setting on the dvd menu. change your video setting from composite, to component.

I expect there is either a power supply issue or one of the amplifiers has failed causing over current to turn it off as a protection to the power supply.

"Opening" ... Please explain what you mean.

Yes if it has a suitable speaker connection available and is nominally 8 ohms impedance Speaker and AV.

Being from 1985 or there abouts, it probably needs some TLC at a Yamaha service centre. May need new capacitors and resolder dry joints for age related issues.