20 Most Recent
LifeView FlyTV MCE TV Tuner/Video Capture/PVR PCI Card (7P1022901020) - Page 8 Questions & Answers
TAKING BACK OFF OF MODEL NM200TAVPE MEGA MOVER LI
It appears there might be a typo or a misunderstanding in the model name you provided. I couldn't find information specifically related to a "NM200TAVPE MEGA MOVER LI." If you are trying to take the back off a device, it's important to note that disassembling electronic devices can void warranties and may require special tools and expertise.
However, if you are looking to remove the back cover of a device, here are some general steps you can follow. Please keep in mind that these steps may not be directly applicable to your specific model:
- Power Off:
- Make sure the device is powered off and unplugged from any power source.
- Check for Screws:
- Look for screws around the edges of the back cover. If there are screws, use the appropriate screwdriver to remove them.
- Pry Open:
- After removing any screws, gently pry open the back cover using plastic opening tools or a case opening tool. Be cautious not to damage the device or any internal components.
- Look for Clips or Latches:
- Some devices have plastic clips or latches holding the back cover in place. Carefully examine the edges for these and use a plastic tool to release them.
- Refer to User Manual:
- Check the user manual or any documentation that came with the device for specific instructions on how to remove the back cover.
- Manufacturer's Support:
- If you're unsure or unable to find information, consider reaching out to the manufacturer's customer support for guidance. They may provide specific instructions or warnings.
Remember, if the device is still under warranty, opening it up may void the warranty. Additionally, certain devices may have sealed backs, making it challenging for users to access the internal components.
If you can provide more accurate information about the device or its intended use, I may be able to offer more precise guidance. If it's a specific product, checking the manufacturer's website or contacting their support is often the best course of action.
Quantum dvd display message " do not watch dvd" in the middle of movie
If your Quantum DVD player is displaying a message saying "Do not watch DVD" in the middle of a movie, it could be due to a variety of reasons. Here are some steps you can take to troubleshoot and resolve the issue:
- Check the DVD for Damage:
- Inspect the DVD for scratches, smudges, or other damage. A damaged DVD can sometimes trigger error messages.
- Clean the DVD:
- Clean the surface of the DVD using a soft, lint-free cloth. Wipe gently from the center of the disc toward the outer edge.
- Try Another DVD:
- Test the DVD player with a different DVD to see if the issue persists. This can help determine whether the problem is with the specific disc or the DVD player.
- Firmware Update:
- Check if there is a firmware update available for your Quantum DVD player. Manufacturers often release updates to address bugs and improve compatibility.
- Check for Region Code Issues:
- Ensure that the DVD is compatible with the region code of your DVD player. If the region codes do not match, it may trigger error messages.
- Reset the DVD Player:
- Turn off the DVD player, unplug it from the power source, and wait for a few minutes. Plug it back in and turn it on. This can sometimes resolve temporary issues.
- Inspect for Foreign Objects:
- Open the DVD player tray and check for any foreign objects (dust, debris, etc.) that may be interfering with the playback. Clean the interior of the DVD player if needed.
- Contact Quantum Support:
- If the issue persists, it's advisable to contact Quantum's customer support. They may provide specific instructions or recommend further troubleshooting steps based on the model of your DVD player.
Remember to consult your DVD player's user manual for model-specific troubleshooting steps and information. If the problem persists and the DVD player is under warranty, consider seeking professional assistance or returning it to the manufacturer for inspection and repair.
I got a un60es610fxza the power button flashes and it has a popping noise when trying to turn it on
The symptoms you've described, including a flashing power button and a popping noise when trying to turn on the TV, indicate potential issues with the power supply or other internal components. Here are some steps you can take to troubleshoot the problem:
- Unplug and Wait: Disconnect the TV from the power source and wait for about 10-15 minutes. Then, plug it back in and attempt to turn it on. This allows the TV to reset and can sometimes resolve temporary issues.
- Check Power Supply: Verify that the power supply to the TV is stable. Ensure the power outlet is functioning correctly, and try plugging the TV into a different outlet. If possible, test the TV with a different power cable.
- Inspect for Physical Damage: Examine the TV for any visible signs of physical damage, such as burnt components or damaged cables. If you notice any, it may indicate a hardware problem that requires professional repair.
- Perform a Hard Reset: Some TVs have a reset button or a specific procedure for a hard reset. Refer to the TV's manual or contact the manufacturer for instructions on how to perform a hard reset.
- Check for Error Codes: Look for any error codes or diagnostic indicators on the TV. Refer to the user manual or contact the manufacturer's support for information on interpreting error codes.
- Professional Inspection: If the issue persists, it's advisable to seek professional help. A certified technician can diagnose and repair internal components, such as the power supply or main board, if necessary.
- Contact Manufacturer Support: Reach out to the manufacturer's customer support for guidance. They may be able to provide specific troubleshooting steps based on the symptoms you've described.
Given the popping noise, it's important to exercise caution and avoid attempting repairs if you are not familiar with electronics. Internal components of a TV can carry high voltages, and improper handling may lead to injury or further damage.
If the TV is still under warranty, consider contacting the manufacturer for warranty support or instructions on the next steps. If not, seeking professional assistance is recommended for a thorough diagnosis and repair.
My portable onn dvd player volume keeps going down by itself.
Check if the volume knob on the DVD player is stuck or damaged. If it is, try cleaning it with a soft cloth and see if that helps.
If the volume knob is not the issue, try cleaning the laser lens inside the DVD player with a cotton swab and alcohol. This can help remove any dirt or dust that may be interfering with the player's operation.
If the above steps do not work, try resetting the device by holding down the power button for about 10 seconds. This action refreshes the system and closes all running processes, potentially resolving the glitch. If this does not work, I suspect you would have to have a repair shot take a look or consult customer service of the device.
Who is the manufacturer of
According to a number of web site blogs, consensus of opinion points to a tv, made in Slovakia and possibly a rebranded bottom end Sharp. It doesn't seem to matter though because TV's are so reliable now and with a 12 month warranty, for £200 with all that on it, who really cares?
It is made for Costco, Sainsbury, Tesco bla bla bla.
When I turn the tv on it remains black . No picture only sound.
Hello, this happens when the HDMI connection on either device has failed or the HDMI cable is bad. Can you still access the television menu with a button on the television or from its own remote? When this does not help and unplugging the television, for some time did not, then take a clear flashlight and shine its light everywhere on the screen. When the backlight is broken, you can still see what is on screen in that small lit spot. This is a common failure and can often be repaired. There are video's about it on YouTube. Capacitors for the power supply hold high voltage so unplug the set from the mains and wait a little before even opening. Still never touch those small towers. When their top, that looks like divided in three parts, isn't flat anymore then there is a power issue and those capacitors must then be replaced.
My provide TV 3200 needs to be reset to work with my OTA indoor
If you're having trouble getting your OTA channels to work on your ProView 3200 flat screen TV, there are a few things you can try:
- Verify that the antenna is correctly and securely plugged in by checking it. Try raising your over-the-air antenna if you're using one, ideally so it's close to a window. To determine out which way your antenna should be pointed, you may also use an online station finder.
- Restart the TV: Press the power button to turn off your TV, then disconnect it from the mains, wait two minutes, plug it back in, and press the power button again to turn it on. Try launching an automated channel search on your TV after it has restarted.
- In the event that your TV is still unable to pick up channels, check the tuner and make sure the coaxial line is in working order.
I hope this helps you restore service to your OTA channels!
Code for dick smith tv
I have read that AWA codes work. 039 worked for me. Try the below. If your universal remote uses 3 digit codes, drop the first zero.
AWA 0041 0066 0039 0187 0404 0481 0442 0067 0586 0246 636 0247 0138 0294 2015 1406 0208 0728
How to fix my TV showing database empty
1. Check your TV's database for issues.
2. Troubleshoot using TV settings.
3. Consult TV manual for guidance.
4. Contact TV manufacturer support if problems persist.
My TV colour has changed
You have lost red which could be the red driver integrated circuit or associated components or it can be the CRT, you will need to let a technician have a look.
SUPER8
Not finding what you are looking for?