Top 20 Bunn BCW Coffee Pot and Decanter Warmer Questions & Answers

Did you let the vinegar mix with the hot water in the tank for 2 hours? If this didn't fix the problem, please call 800-352-2866 with the model and date code and we will be happy to assist you with this problem.

Somewhere inside you should find a small rotary thermostat. Also make sure the heating element is completely clean by using a quality descaler like CLR. A lot of people use white vinegar but it is not that effective on coffee makers. Make sure the heating element under the carafe is working, because that is heating up as the coffee is brewing. ..

Question edited for clarity and toss in a load of CAPS. It is dated with a non intuitive, none readable code. You can see examples here. Where is my Date Code? BACK OF BREWER Sticker on the lower back of brewer BOTTOM OF BREWER Sticker attached to the bottom baseplate of your brewer. Note: Allow water in tank to cool. Drain water before turning over.

Where is my Date Code? - BUNN

More here https://www.google.com/search?q=Bunn-o-Matic+HB+coffee+maker+read+the+date+code ..

unplug machine and turn upside down and pour out coffee and water mix (if water was in reservoir) If necessary turn over and fill will water and repeat.

Replace and run a pot of clean water thru it.

To locate the date code on your BUNN BT Velocity brewer, you can try the following:

1. Check the bottom or back of the brewer: Look for a label or sticker on the bottom or back of the machine. The date code is typically printed on this label.
2. Inspect the sides or inside the brewer: In some cases, the date code may be located on the sides or inside the brewer. You may need to remove any panels or covers to access the label or sticker.
3. Consult the user manual: If you have the user manual for your BUNN BT Velocity brewer, it may provide information on where to find the date code. Refer to the manual for specific instructions or contact BUNN customer support for assistance.

If you are still unable to locate the date code on your brewer, I recommend reaching out to BUNN customer support directly. They will be able to provide you with accurate information and guide you in finding the date code on your specific model of the BT Velocity brewer.

Normally that would be an easy fix if the water just continued to flow. You just replace the water inlet valve and they can stick open or partially open. But you say if you power off, the flow stops. That sounds like the control board is supplying residual power to it. Control boards are expensive so I would call for service. Or you can try some of the fixes here. https://www.google.com/search?q=bunn+coffee+maker+cwtf15+replacement+water+inlet+valve More here https://www.google.com/search?q=bunn+coffee+maker+cwtf15+water+not+shutting+off ..

shorted water heater element

Question edited for clarity. Question moved from Cars and Trucks. Probably needs a new water inlet valve. Google Bunn model water inlet valve

Bunn Valves, Solenoids & Fittings ' Parts Town

https://www.partstown.com > bunn > parts 266 items - How to find your Bunn model and serial number ... Bunn 27370.0007 Solenoid Valve Assy, Bypass-Plastic, 120V. Add to My Parts. In My Parts. https://www.google.com/search?q=Bunn+model+water+inlet+valve ..

Question edited for clarity. Question moved from Refrigerators. Hi again Bill Making a new post as a follow-up doesn't work here at Fixya. Posts are not threaded or linked, so this post has no context to your previous post. What you wrote here should be in the older post as a reply to Brett and I. You just click COMMENT under our answers to you. The benefits are that it keeps everything together and we get a notification that you require further help. And apparently is is a 'Bunn GRX-B Coffee Maker'. Capitalization and dashes are important to the search :>) https://www.fixya.com/support/t29863408-need_temp_limit_switch_garbage_bunn ..

Not sure your model name is correct and we always need numerical model names here. Bunn are such a well known name in coffee machines, I find it disappointing that they say ANY machine is not repairable. I found some Training Manuals and I found a 'Thermostat Limit Kit'. https://www.google.com/search?q=bunn+grab+fast+brew++temperature+limit+switch The search query would be Bunn (numerical model number) temperature limit switch ..

i think you may have to get a new one

only from BUNN AND POSSIBLYTHRU A DEALER

You can ask them direct https://commercial.bunn.com/44600.0000 https://www.google.com/search?q=Bunn+My+Cafe+MCR+(44600.0000) ..

check the link below https://www.google.com/search?q=Bunn+bad+tic+clock+location&oq=Bunn+bad+tic+clock+location&aqs=chrome..69i57&sourceid=chrome&ie=UTF-8

Hell and good day, this simply means that it need to be service Thanks for coming.

Yes https://www.google.com/search?q=Cleaning+a+bunn+power+aid+slushiy+machine+filter&rlz=1C1QJDB_enCA643CA644&oq=Cleaning+a+bunn+power+aid+slushiy+machine+filter&aqs=chrome..69i57&sourceid=chrome&ie=UTF-8 ..

google item and error code, if no owners manual try: https://www.manualslib.com

Im assuming you tried it more than once and the tank is full when you start? If your doing manual fill pour over the timer has nothing to do with that. If it's plumbed with a water line, before you start changing your timer for the brew cycle, first try the easy fix which is unscrew the spray head. it's the piece the water comes out to the basket. Take the cleaning spring tool and rotate it as you push it thru the tube you just unscrew the spray head from. As your pushing it thru it has two turns in it . Just rotate and push until you have gone thru the second one and then it's clear to the water tank. Unfortunately this doesn't always get it unplugged. Where the tube goes into the water tank there is silicone hub on the part that's in the tank and it can keep some of the lime buildup from being removed. You will have to take the top off and remove the tube to clean it if that happenes. Dont forget to unplug it first. The other common spot for a restriction is where the water leaves the pan your pouring into. You need to remove the pan to get the spray tube out anyway so look also at the big nut that holds the pan onto the tank.sometimes the hole will plug in the center .

Couple of ideas.

Your weak coffee could be due to the machine not getting hot enough, which is usually caused by calcium scale buildup on the heating element (the "burner").

Try descaling with a citric-acid based cleaner, such as Dezcal or Durgol.

The second is the coffee your using is a weak blend. Try changing to a different coffee and see if the strength is better.