Olympia InfoGlobe Caller ID - Answered Questions & Fixed issues

When it is flickering, can you still read it? Mine didn't flicker. Maybe it just needs new batteries. I did find that mine had trouble working once I switched over to AT&T Uverse internet/phone service.

i thing so call you phones service people they will help you

If you can afford to , reset your phone. Otherwise, your display might have an error

Hi, usually this red light is a "new message" indicator when it's on, the normal condition should be off. If the caller ID function is not working could be cables misconnected, the connector labeled as line should be connected to wall line outlet, the connector labeled as phone should be connected to your telephone. In the worst of cases if the connections are OK, there's a problem with the line or the caller ID unit.

There are usually several available on eBay and Amazon.

Here is a plain text version of the manualhttp://archive.org/stream/OlympiaInfoGlobeOl3000.2Manual/OlympiaInfoGlobeOl3000.2Manual_djvu.txtIt's a bit tricky to read due to it being in plain text, but the necessary words of instruction are all there.

I am looking for a web site to print out the manual for the olympia ol3000.2. Is there a web site that will let me do this?

Hi,

Your unit has some settings problem.You have to reset the unit.Try resetting the unit.If still the problem persist you have to reset the infoGlobe.txt file using PC interface cable.Which they will do in service centre only.

http://www.lima.com.tr/BasicTiger/Applications/PDF/appn_071e_The%20magic%20globe.PDF

Please do rate the solution if the issue is resolved or post a comment for further assistance.


Thank you for using fixya have a nice day:-)

It can still work if you can take the phone to computer engineer for repairs.

check your battery or your adapter

Sonar, Sorry, the LED can not be partially fixed. It has to be replaced wholly.

My dear:
Very Best Solution:You Go To Service & Sim Office and Get The Puk code And Pin code From Office oprator
Enter The Puk code and Yes
Enter The pin code and Yes
So Puk code Open and Problem will Quickly Solved
But:
Don't try to enter a PUK code without knowing the right one.
You need to call your service provider to get this code.
It can be as many as 8 digits, and it is random. If you enter too many wrong codes,
you can permanently damage the device. So Please You Go to Service office
and Get the Duplicate Sim From Office Oprater Same Your No Problem will Solved

i dont know what is the answer....im so sorry for that...i have question...who post this question?

for most problews, including caller id, follow these instructions in order:

Put the battery into the battery compartment and connect to the
connectors inside the battery compartment.
Connect the power adapter and telephone cord into matching jacks on the under side
of the base.
Plug the power adapter into the electrical outlet. Plug the telephone cord into the
telephone socket.

my caller id was not working, but everything else was. I followed the instructions above EXACTLY IN ORDER and the caller id is now working.

some of my leds are out.

reset buttons not making good connections...try pushing harder or wiggle the buttons back and forth while pushing down on them...sometimes they make contact that way....if you can get the unit to reset doing that then...have the button assembly cleaned out in the future...good luck

silvio

You are possibly in the demonstrate mode. If that is the case, press and hold the right key for a few seconds.

If the mechanism is not turning at all, hold down the left key to start it.

I have the manual and can tell you what it says:
(this worked for me last year when we went off daylight savings, but for some reason, It doesnt seem to work anymore. I can't imagine that I did anything different then. You can try, though.)
Enter (or leave) the Demonstration Mode by pressing the right key for at least 1 second.
Then, by pressing SELECT key, you are SUPPOSED to be able to scan a menu which lets you pick date format, time format, etc.

This no longer works for me, and the instructions also have a contradictory comment that says the SELECT key is disabled in this mode. But perhaps this will work for you.

I would also appreciate instructions if anyone knows what I am doing wrong.

I just printed a manual in pdf form go to,http//smarthome.com/manuals/5109.pdf