20 Most Recent Keurig Special Edition B60 Coffee Maker - Page 4 Questions & Answers

Seal defective...replace.

Port (Needle) is plugged. Clean with pin. See Manual.

That is the port ring and it is exposed or fell out. Replace, see manual for directions.

Primer defective and needs replacement.

TRY...1. Lift up the water reservoir and drop it back into place. There is a magnet that has to be in the right position and putting the reservoir back into place causes it to go back where it should be. 2. It may be time to descale. Most models will give you a message when it's time to have the mineral deposits cleaned. HERES HOW TO DO THAT... Empty water resevoir. Disable auto off. Pour approx 48 oz of undiluted white vinegar into resevoir. PLace large mug on drip plate, run brew cycle, dump contents of mug in sink. DO NOT USE A K-CUP. Repeat this process until the add water light is indicated. Let brewer stand for at least 4 hours while still on. Discard any residual vinegar in the resevoir and rinse thorughly. AFTER approx 4 hours...fill resevoir with water. RINSE: PLace a large mug on the drip plate and water brew cycle. Pour the contents of the mug into the sink. REPEAT this brew process until the add water light is indicated. YOU MAY NEED TO REPEAT THIS "RINSE" PROCESS if you notice any residual taste.

Turn off your brewer and use an unfolded paperclip to clean out the holes in the top needle

It may be time to descale. Most models will give you a message when it's time to have the mineral deposits cleaned. HERES HOW TO DO THAT... Empty water resevoir. Disable auto off. Pour approx 48 oz of undiluted white vinegar into resevoir. PLace large mug on drip plate, run brew cycle, dump contents of mug in sink. DO NOT USE A K-CUP. Repeat this process until the add water light is indicated. Let brewer stand for at least 4 hours while still on. Discard any residual vinegar in the resevoir and rinse thorughly. AFTER approx 4 hours...fill resevoir with water. RINSE: PLace a large mug on the drip plate and water brew cycle. Pour the contents of the mug into the sink. REPEAT this brew process until the add water light is indicated. YOU MAY NEED TO REPEAT THIS "RINSE" PROCESS if you notice any residual taste.

leave unpluged for three days ,then try it.

Call CS and let them walk you through the solution. I did just that and it did not work. Called back the next day and they are sending me a new unit. I just have to send back the k-cup holder at my expense. I will re-register this new Keurig and I am good to go for another year. BTW, I have had my 'prime problem' Keurig for 9 months, only make one or two cups a day.

all the lights are blinking its clean, descaled, filled with water and the power button and all the buttons just blink and it wont brew just had this machine less than 6 months and the machine will only quit blinking when i unplug it and yes ive tried different outlets when i plug it back in all the lights start blinking again and it wont brew i want a solution to this problem and i dont want to be sent to another site where they charge me to answer a question the $119 i payed for the thing should be enough im ready to throw it out the window im so frustrated with it

of course, you have to select one of them from the three

It is cheap machine for the price. The design is inefficient . Consider another brand. But in all fairness, normal maintenance is needed. 90 % of the reason things break down is due to little or no maintaining of the equipment.

The most common problem is this category is the no power, or Keurig not turning on, problem. When this happens it is usually because of the failure of the transformer inside the machine. The low voltage transformer is located underneath one of the solenoid valve in most of the machines. The hoses to this valve and/or the valve will leak a bit and drop water down onto the transformer. Electrical components and water do not play well together. The transformer will soon go bad when it gets water on it. For that matter, many brewing problems are caused by the air pump getting wet from the same leaking point also. The air pump can sometimes be fixed, but the transformer is not even available to be bought as a replacement part, and there is no fixing them.

Hi,

The problem is often that the machine develops a leak in the hose that is rightover the transformer...the water drips onto the transformer and kills that...then you have no power to run the machine.

Here is a tip that I wrote about this problem...

Keurig OneCup Coffee Brewer will not turn on
heatman101

--=-
=-

Get it cleaned, use a aircompressor