20 Most Recent Hotpoint 24 in. DWF32P Free-standing Dishwasher - Page 3 Questions & Answers

REPLACE WATER INLET SOLENOID ON WASHER

REPLACE TIMER

I have a similar problem.When the water stops entering,I momentarily turn on my main kitchen cold water tap, and believe it or not,the machine carries on working!!

to isolate fault,remove bottom front panel,turn off main water,put a tray under machine, remove inlet pipe frompump at front of machine. for a second to see if you have flow that far. If so trouble is in machine. Dig the filter out of th pump entry .It could be blocked

you ..dont need to get into the back.With the bottom front panel off,disconnect the waste pipe frm the pump on the right and pull it through from its other end.

your leak might be caused by a faulty door gasket.as far as your other problem try turning off the power at breaker for 30 sec. to reset cpu

You need a new inlet valve. Axcessed through bottom panels below door there are screws in the four corners of the upper one. Inlet valve is where the water line meets a plastic body with wires going to it. www3.sears.com for parts.

clogged drain or faulty pump would not cause the appliance to leak which it is if understand correctly. if amount of water is considerable, then it is likely a perished pipe or similiar. older hotpoints do not have a base so tilt it and have a look come back to me if you like

Here's what you can do to address this issue:

1. Check the Salt Level: Ensure that the salt reservoir is filled with dishwasher salt. The dishwasher needs salt to soften the water and improve the cleaning performance. If the salt level is low or empty, refill the reservoir with dishwasher salt.
2. Check the Salt Dispenser Cap: Make sure that the salt dispenser cap is securely closed. If it's not closed properly, it can cause the "X" symbol to appear on the display.
3. Reset the Dishwasher: Try resetting the dishwasher by turning it off at the mains power supply for a few minutes, then turning it back on. This can sometimes clear error codes and restore normal operation.
4. Check for Blockages: Ensure that the salt dispenser and its inlet are free from any blockages or obstructions that could prevent salt from dissolving properly.
5. Consult the Manual: If the issue persists, refer to the dishwasher's user manual for troubleshooting steps specific to your model. The manual may provide additional information about error codes and how to resolve them.

If none of these steps resolve the issue and the "X" symbol continues to appear on the display, it may indicate a more significant problem with the dishwasher that requires professional diagnosis and repair. In such cases, contacting Hotpoint customer service or a qualified appliance technician for assistance is recommended.

https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=&cad=rja&uact=8&ved=2ahUKEwjC_-mpw5SCAxUpCnkGHWfJDewQFnoECA0QAw&url=https%3A%2F%2Fwww.repairclinic.com%2FRepairHelp%2FHow-To-Fix-A-Dishwasher%2F28-95--%2FHotpoint-Dishwasher-Lights-Flashing-Or-Blinking%23%3A~%3Atext%3DIf%2520the%2520dishwasher%2520lights%2520are%2Cis%2520functioning%2520properly%2520or%2520not.&usg=AOvVaw1Zr97Zu3aDvX9lj1mrJZ56&opi=89978449 also check water inlet valve.

Help in the link https://www.google.com/search?q=Hotpoint+Dishwasher.+Salt+light+won%27t+go+off ..

Each time you push delay, it should add 2 more hours. If not, it will only delay for 2hours.

I have same issue, have just worked out that: 1=Intensive 2=Normal 3=Daily 4=Prewash 5=Eco

Check the leak tray inside the base of the machine and see if there is water in there. There is a sensor to detect small leaks.

At 5 months old it should be still under warranty and qualify for free repair...

try just putting it in the bottom of the machine where the water goes

The rear legs may not be adjustable - only the front.