Top 20 Hotpoint 23 in. BF50 Built-in Dishwasher Questions & Answers

the problem will be in the circuit to the door opening the door and it trips the breaker indicates that the hinge is rubbing on a wire or making the harness move to ground out

Hi,

Here is a tip that I wrote about dishwashers and them leaking.Leaking Dishwasherheatman101

there is a screen in the fill valve it could be getting plugged, or you have a kink in the fill pipe , [email protected]

Hi ,When this happens I keep the button with the letter "P" Pressed until the fault lifgt resets,my row of buttons is inside the top edge of the unit.

New Spray arm split around center joint so when it gets hot it opens up spraying water under door

 

take it back for another

 

Alan

Andy, leave the breaker off and remove the toe panel (bottom panel) from the dishwasher. Remove the cover of the junction box where the cord connection or wiring is made. Look at the wire caps and see if they are not burnt. Sometimes these connections become loose and arch, tripping the breaker. If so, cut the wires, strip a new end and reconnect. Catriver...post back.

Here's what you can do to address this issue:

1. Check the Salt Level: Ensure that the salt reservoir is filled with dishwasher salt. The dishwasher needs salt to soften the water and improve the cleaning performance. If the salt level is low or empty, refill the reservoir with dishwasher salt.
2. Check the Salt Dispenser Cap: Make sure that the salt dispenser cap is securely closed. If it's not closed properly, it can cause the "X" symbol to appear on the display.
3. Reset the Dishwasher: Try resetting the dishwasher by turning it off at the mains power supply for a few minutes, then turning it back on. This can sometimes clear error codes and restore normal operation.
4. Check for Blockages: Ensure that the salt dispenser and its inlet are free from any blockages or obstructions that could prevent salt from dissolving properly.
5. Consult the Manual: If the issue persists, refer to the dishwasher's user manual for troubleshooting steps specific to your model. The manual may provide additional information about error codes and how to resolve them.

If none of these steps resolve the issue and the "X" symbol continues to appear on the display, it may indicate a more significant problem with the dishwasher that requires professional diagnosis and repair. In such cases, contacting Hotpoint customer service or a qualified appliance technician for assistance is recommended.

https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=&cad=rja&uact=8&ved=2ahUKEwjC_-mpw5SCAxUpCnkGHWfJDewQFnoECA0QAw&url=https%3A%2F%2Fwww.repairclinic.com%2FRepairHelp%2FHow-To-Fix-A-Dishwasher%2F28-95--%2FHotpoint-Dishwasher-Lights-Flashing-Or-Blinking%23%3A~%3Atext%3DIf%2520the%2520dishwasher%2520lights%2520are%2Cis%2520functioning%2520properly%2520or%2520not.&usg=AOvVaw1Zr97Zu3aDvX9lj1mrJZ56&opi=89978449 also check water inlet valve.

Help in the link https://www.google.com/search?q=Hotpoint+Dishwasher.+Salt+light+won%27t+go+off ..

Each time you push delay, it should add 2 more hours. If not, it will only delay for 2hours.

Check the leak tray inside the base of the machine and see if there is water in there. There is a sensor to detect small leaks.

The rear legs may not be adjustable - only the front.

try just putting it in the bottom of the machine where the water goes

At 5 months old it should be still under warranty and qualify for free repair...

https://searchmanuals.net/search7/?keyword=%2Bowners+%2Bmanuals&gclid=CjwKCAiAqt7jBRAcEiwAof2uKwzE1jBmBNKl9hqWd4TyeToXsj80tGOrdxRc3s6LGEWtoEA-xsOXLBoCIhQQAvD_BwE

I once bumped the water supply shut-off under the sink and turned the supply off at the shutoff. Other than that, have you had any work done on the hot water tank recently ?

I also encountered a similar problem. It was not possible to contact the service center, so I searched for a solution on the Internet, and found it on this site - https://washingcodes.com/blog/#.XFwRwFUzaUk

Hi there, I am from the UK so model numbers vary but all basically the same. Do not fear it is simple really. You need to take the door from it's hinges first. It will either have screws or bolts to the door or frame of the machine. Now you have the door dismantled and in your hands. place upside down and you will see screws ??? they will be situated around the door ?? the door comes in two parts and the glass is sandwiched between the two parts. ( Take photo if in need ) you will see see a metal shaft and spring where your handle will fit. All the best and Happy Christmas from the UK

https://www.google.co.in/search?q=Have+Hotpoint+Dishwasher+model+DF61N+Need+wiring+diagram&rlz=1C1KMOH_enIN790IN790&tbm=isch&source=iu&ictx=1&fir=hfT4fUt27enaFM%253A%252CqTo0BQBDnQ0BcM%252C_&usg=AI4_-kSIDXjWgo94dL3QyAmXQKmlBHCuTQ&sa=X&ved=2ahUKEwiBisX1v_7eAhXDrI8KHfE-AMMQ9QEwAnoECAYQCA&cshid=1543662915079001#imgrc=hfT4fUt27enaFM: