Hotpoint 23 in. BFV62 Built-in Dishwasher - Answered Questions & Fixed issues

I think I've seen this one on a similar dishwasher. You have an internal leak. Because yours is built in it's not easy to check but If you can lift it out and angle the machine forward about 45 degrees - you will need some towels! ... This might be a temporary cure but I ended up sealing the cabinet by opening up the case and using a mixture of silicon sealant and duct tape.

Hi,
Here is a tip that will help you to find out why water will not come into the dishwasher...
Dishwasher Trouble No Water entering Dishwasher
http://www.fixya.com/support/r4021363-dishwasher_trouble_no_water_entering

heatman101

Hi,
Check your heating element..

Dishwasher Problems The Heating Element not Working
http://www.fixya.com/support/r4589033-dishwasher_problems_heating_element_not

Dishwasher Maintenance
http://www.fixya.com/support/r4319937-dishwasher_maintenance

heatman101

Asker's Testimonial " expanation very clear. will give it a go and see how simple it was. thanks Ronnie " - ronnieshomes

go to hotpoint web address and they will tell you.i would suspect main circuit board.adrian,,,,

Here's what you can do to address this issue:

1. Check the Salt Level: Ensure that the salt reservoir is filled with dishwasher salt. The dishwasher needs salt to soften the water and improve the cleaning performance. If the salt level is low or empty, refill the reservoir with dishwasher salt.
2. Check the Salt Dispenser Cap: Make sure that the salt dispenser cap is securely closed. If it's not closed properly, it can cause the "X" symbol to appear on the display.
3. Reset the Dishwasher: Try resetting the dishwasher by turning it off at the mains power supply for a few minutes, then turning it back on. This can sometimes clear error codes and restore normal operation.
4. Check for Blockages: Ensure that the salt dispenser and its inlet are free from any blockages or obstructions that could prevent salt from dissolving properly.
5. Consult the Manual: If the issue persists, refer to the dishwasher's user manual for troubleshooting steps specific to your model. The manual may provide additional information about error codes and how to resolve them.

If none of these steps resolve the issue and the "X" symbol continues to appear on the display, it may indicate a more significant problem with the dishwasher that requires professional diagnosis and repair. In such cases, contacting Hotpoint customer service or a qualified appliance technician for assistance is recommended.

https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=&cad=rja&uact=8&ved=2ahUKEwjC_-mpw5SCAxUpCnkGHWfJDewQFnoECA0QAw&url=https%3A%2F%2Fwww.repairclinic.com%2FRepairHelp%2FHow-To-Fix-A-Dishwasher%2F28-95--%2FHotpoint-Dishwasher-Lights-Flashing-Or-Blinking%23%3A~%3Atext%3DIf%2520the%2520dishwasher%2520lights%2520are%2Cis%2520functioning%2520properly%2520or%2520not.&usg=AOvVaw1Zr97Zu3aDvX9lj1mrJZ56&opi=89978449 also check water inlet valve.

Help in the link https://www.google.com/search?q=Hotpoint+Dishwasher.+Salt+light+won%27t+go+off ..

Each time you push delay, it should add 2 more hours. If not, it will only delay for 2hours.

I have same issue, have just worked out that: 1=Intensive 2=Normal 3=Daily 4=Prewash 5=Eco

Check the leak tray inside the base of the machine and see if there is water in there. There is a sensor to detect small leaks.

At 5 months old it should be still under warranty and qualify for free repair...

try just putting it in the bottom of the machine where the water goes

The rear legs may not be adjustable - only the front.

https://searchmanuals.net/search7/?keyword=%2Bowners+%2Bmanuals&gclid=CjwKCAiAqt7jBRAcEiwAof2uKwzE1jBmBNKl9hqWd4TyeToXsj80tGOrdxRc3s6LGEWtoEA-xsOXLBoCIhQQAvD_BwE

I also encountered a similar problem. It was not possible to contact the service center, so I searched for a solution on the Internet, and found it on this site - https://washingcodes.com/blog/#.XFwRwFUzaUk

I once bumped the water supply shut-off under the sink and turned the supply off at the shutoff. Other than that, have you had any work done on the hot water tank recently ?

Hi there, I am from the UK so model numbers vary but all basically the same. Do not fear it is simple really. You need to take the door from it's hinges first. It will either have screws or bolts to the door or frame of the machine. Now you have the door dismantled and in your hands. place upside down and you will see screws ??? they will be situated around the door ?? the door comes in two parts and the glass is sandwiched between the two parts. ( Take photo if in need ) you will see see a metal shaft and spring where your handle will fit. All the best and Happy Christmas from the UK

https://www.google.co.in/search?q=Have+Hotpoint+Dishwasher+model+DF61N+Need+wiring+diagram&rlz=1C1KMOH_enIN790IN790&tbm=isch&source=iu&ictx=1&fir=hfT4fUt27enaFM%253A%252CqTo0BQBDnQ0BcM%252C_&usg=AI4_-kSIDXjWgo94dL3QyAmXQKmlBHCuTQ&sa=X&ved=2ahUKEwiBisX1v_7eAhXDrI8KHfE-AMMQ9QEwAnoECAYQCA&cshid=1543662915079001#imgrc=hfT4fUt27enaFM:

Could be the pump