Top 20
Hotpoint 24 in. HDA3400G Built-in Dishwasher Questions & Answers
The drain is not clogged or blocked and the line
their will some water that always remains in the pump below the fliters is should never be visible in the tub once cycle is over but it must always be there to keep the seals moist to prevent them from dry rotting
Water doesnt drain and water nozzle doesnt
Hi
Dishwasher not draining issue usually occurs due
to kinked drain pipe, clogged drain filter or drain pump. First make sure that
the drain is not clogged and remove clogs if present. If no visible lint is
present then remove the lower front access panel to check the drain filter and
drain pump for any clogs, you'll need to clean the drain filter and drain pump
completely. Also, check for any food pieces stuck near the pump impeller &
clean the chopper assembly. Please note that dishwashers don't drain out the
complete water such that heating element doesn't overheat. Hope this helps...
Please post back for any further assistance.
Daniel
. The dishwasher fills with water but will not
Same problem here. It's been a while since we used it. HDA 3440GO2SA. I think I've narrowed it down to the motor seizing. I get 12.2 ohms on the windings and a local tech says the windings are good then. Some decent troubleshooting videos here
http://www.appliancehelponline.com/dishwashernotrunning.html.
Turn the breaker off for the unit (so you have no power), remove the bottom panel and kick plate. take a screw driver and try to turn the motor fan blades. If it turns really hard keep turning it until it loosens up. If it turns freely, pull the plug, test the power coming in with your multimeter (requires turning breaker back on, of course, but after the leads are inserted in the plug). You should have around 120 volts with the door switch activated and wash cycle on. Anyhooo...I plan on trying to pull the hub and clean it up, put some di-electric grease on it and re-assemble. If that doesn't work then I'll debate whether to spend 150+ on a new motor or just get a new dishwasher...lol.
How old is my Hotpoint
The motor is stuck. If you remove the lower cover and see a square aluminum motor it is less than 7 years old. Make sure power is off at breaker and rotate the motor shaft
by turning the fins inside the motor.
If the motor is black and round you have to turn
the fan blade which is located in a slot between the metal pump and the plastic
pump. Also once freed, a light shot of silicone or WD-40 (silicone works better) at the
bearing ends. Also check pump for leaks around the drain solenoid (shiny shaft attached
to a plastic triangle). If it's leaking during pumpout, the seal has failed. The pump runs
around 100 dollars typically. Hope this helps.
Will not drain
a couple of things to look for ...you want to make sure the drain is clear...usually you can remove line from under sink and check connection for obstruction and clean out... also remove screen from lower portion of dishwasher and check inside there for any foreign materials. alot of times you have to remove spray arm to gain access ,but a fairly easy process. if all that looks good take bottom panel off of dishwasher and under unit you will see a square metal device with a solenoid on it and usually has a short rod on it attached to the pump assembly.. this is a real common problem the drain solenoid goes bad... if you turn dial slowly you should see this solenoid move up and down at different times in the cycle. you should also here a click and it begin to try and drain..if it doesnt move then it most likely is bad.. you can also unplug and see if your getting power to it in the drain cycle on the timer .... if it is moving then ot is possible the drain pump has failed...hope tis helps you out... p.s. if you have a garbage disposal or recently installed a garbage disposal a common proble people forget to knock the plug out on the neck assembly where the drain line attaches.(only if you recently installed a garbage disposal does this pertain)
The dishes are not getting completely clean. Could
Hi,
I
have an older dishwasher also and recently my wife also complained
about it not cleaning right... so me being the man I am tried in vain
to clean the things... Bought new spray arms online and installed
them in minutes...now the thing works like new... However I have also
found that if the heating element goes bad then that also can mess
things up bad... So I would buy new spray arms, and also check out
the heating element to make sure it is working... Here is a tip that
will help you with the online buying...
Dishwasher
Spray
Arms not Spinning
How
to Buy Appliance
Parts Online
A
bad heating element causes many problems in
dishwashers...
Dishwasher Problems The Heating
Element not Working
Dishwasher
Maintenance
heatman101
Asker's Testimonial "explanation very clear. will give
it a go and see how simple it was. thanks Ronnie " -
ronnieshomes
...............
I have an hda3400go2ww, and
Hi
White film deposits are observed if water is hard or when you are using more detergent than needed, try filling detergent cup half way. Try using white vinegar after the wash cycle is complete, run a complete cycle. Also turn down the heat on the hot water fed to the dishwasher. Try using water softener for better results.
You can also add vinegar in the final rinse cycle.
Hope this helps... Please post back if more information is required.
Daniel
Why doesn't the dishwasher drain?
The problem is likely a blockage in the drain line that runs from the dishwasher to the sink. you should take the panel out from under the door and then disconnect the drain line and check for a blockage.
If you have any further questions please feel free to ask.
I have a hotpoint HDA3400 dishwasher and it will
Hi
This is happening due a a faulty fill valve or due to blockage in fill hose. Please check the water inlet hose, try removing it and check for any blockages. If the inlet water hose is fine then you'll need to check the water inlet valve/fill valve. Use a multimeter to check the continuity on fill valve. Make sure the connections on the fill valve/s are fine. Hope this helps... If it does please do not forget to accept the solution or post back for assistance.
Daniel
Not finding what you are looking for?