20 Most Recent Reddy Heater-30-55,000 BTU Variable - Page 7 Questions & Answers

I have one similar, needs a new fan or new unit, anyway on mine I have to plug it into both propane and electrical and will not light unless the fan is plugged in, saefty from it blasting flames\fumes out the back

Could be the vanes in the pump are worn out not producing enough pressure for the fuel to blow out properly resulting in shutdown(for safety). Go online and see if you can get a pump rebuild kit to rebuild pump

Hi,

Here are a couple of tips that I wrote that tell you how to troubleshoot a Torpedo or Reddy heater...

Reddy Heater - Troubleshooting Torpedo Heaters

Torpedo Heater Pump Pressure Adjustment

heatman101

replace the rotor 1/2 inch thick

tnpdew,

See my tip at http://www.fixya.com/support/r4258201-fix_gas_reddy_heaters_will_not_continue .

Thanks for using FixYa and for the great rating. Please consider a testimonial. Thank you.

hardrocko

http://www.reddyparts.com/pressure.htm

I have a LP gas version. I had to disconnect some kind of sensor (looks like a watch battery with 2 red wires). I made a jumper wire and put in place of red wires. Works fine now. This sensor might be an Oxygen sensor.

Maybe replace the thermocouple.

either low on fuel, or has restricted/blocked passage ways. the regulator may as well be bad too.

Yes you can run Diesel in this heater but you will have to turn the pressure up on the back of the pump.
You want the nose cone to be a good glowing orange and with Diesel you may need more air pressure to achieve the proper burning of the heater with the least amount of fumes.

Thanks

M Cramer

www.allpartsinc.com

This can be from either a bad connection from the thermocouple to the gas valve or it could be a bad high limit switch.

If you run a jumper wire between the two leads on the thermocouple and the units runs then you may need to replace the High limit Switch.
If that does not solve the problem then clean the end of the thermocouple lead that goes into the gas valve.

Thanks

M Cramer

www.allpartsinc.com

This is normal. It has a time limit to fire off. The heater will cut off if it does not light.It sounds like it is never lighting up. Check your ignition source. I am not sure if you have a spark plug type or a glow bar.

Sorry to read about your problem, I hope this helps you out.

yes you can with no problems
I tried to help you. Please help me and Rate/Vote on my response. We take the time to answer your question. take the time to rate us.Thanks and good luck

4 Thumbs - Very Helpful
3 Thumbs - Helpful

The pump is not applying enough pressure to allow sufficient fuel volume to the plug. if the plug is not receiving a proper spray to vaporize the fuel at contact, it will not provide enough flame.

Check the flame sensor. It is probably dirty.Use a soft rag to wipe of the photo eye.

firedragonre,

If you know that you are getting gas the unit either has a bad or mislocated igniter or a bad thermal valve in the gas metering assembly. I have a tip at http://www.fixya.com/support/r4258201-fix_gas_reddy_heaters_will_not_continue which explains the problem, how to repair the unit and where to get the necessary parts.

Thanks for using FixYa and for the great rating.

hardrocko

Hi,

Here are a couple of tips that I wrote that tell you how to troubleshoot a Torpedo or Reddy heater...

Reddy Heater - Troubleshooting Torpedo Heaters

Torpedo Heater Pump Pressure Adjustment

heatman101

They are grounds, and should have two screws on the burner tray to hold it from moving. On my heater this is where the grounds get attached. It gives the igniter a dedicated direct ground.

No fuel!! Several things can cause this, empty fuel tank, dirty fuel filter, plugged screen in the nozzle assembly,or plugged nozzle. So lets clean up the fuel system by first removing the top section of the heater and exposing the burner tray. Remove the tray and locate the fuel nozzle, remove the nozzle, now they say you can not clean them, I say with a q-tip, tooth pick and carb cleaner you can just be careful not to damage the nozzle. Behind the nozzle is a screen assembly these corrode at times so clean it up too. Below the nozzle assembly is the flame sensor, clean this with windex and a soft terry cloth rag, make sure it will have a clear unobstructed view of the flame.Put the nozzle assembly back together, and now inspect the fuel line for cracks, holes,and dry rot replace if necessary. Trace the lines down to the side where they come thru the case. Remove the side cover and locate the fuel line and in line filter, remove the filter. Cleaning this is easy you need a compressor and blow gun, all you do is blow air backwards thru the filter and instantly its clean. Inspect fuel lines and reassemble. Now make sure that you have clean fuel in your tank, and there is no water in it as well.Plug it in and you should now be heating like new. If not it could be your fuel pump!

The fan motor runs regardless of the igniter as it is also the fuel pump. Possibly you may need to replace the motor but try this first. Remove the top section of the heater this exposes the fan motor, try spinning the motor by hand,it should spin freely if it does not try some light oil in the front and rear bearings of the motor and turn it by hand until it frees up. You may need to do this several times!! Now that it is spinning free put the heater back together and try it out. If it does not work a new motor is in your future. Hope this works out for you.