Top 20
Nor-Lake Walk In Cooler 6ft x 8ft Norlake Indoor No Refrigeration - Page 9 Questions & Answers
Defy fridge only works on the freezer side. The fridge side is warm! What could be the problem.
The freezer provides the cold air for the fridge via a vent at the back of the fridge. If you have a fridge freezer where the freezer is on top of the fridge, sometimes the vent can get blocked by ice. You would have to remove the food from the freezer and remove the back panel to look. Ice can be removed with a hair dryer or a heat gun.
The other possibility is that the recirculation fan in the fridge has stopped spinning.
Or it needs more gas although this is unlikely.
3/2/2023 5:33:15 PM •
Refrigerators
•
111 views • 0 helpful votes
My water dispenser says I've ran out but I filled it up , and the light keeps flashing what do I do
If your water dispenser on your refrigerator says that it's out of water even though you have already filled it up, and the light keeps flashing, there may be a few things you can try to fix the issue:
1. Check the water supply: Make sure that the water supply line to the refrigerator is turned on and that there are no kinks or obstructions in the line that could be preventing water from flowing to the dispenser.
2. Reset the dispenser: Try resetting the dispenser by unplugging the refrigerator or turning off the power at the circuit breaker for a few minutes, then turning it back on again. This can sometimes clear up temporary glitches in the system.
3. Check the filter: If your refrigerator has a water filter, check to make sure it is not clogged or needs to be replaced. A clogged filter can prevent water from flowing properly to the dispenser.
4. Contact the manufacturer or a professional: If the above steps do not resolve the issue, it may be a more complex problem that requires the attention of a professional technician. Contact the manufacturer or a professional repair service for assistance.
It's important to address the issue as soon as possible, as a malfunctioning water dispenser could lead to other issues or damage to your refrigerator.
4/25/2023 3:19:35 AM •
Refrigerators
•
30 views • 0 helpful votes
I have a 2 door 48 bottle #272 48 03 51W and it started beeping, and also the left flashes on and off. but only on the right side. is there anyway to shut off just one side.
It sounds like you have a wine cooler with two temperature zones, and one of the zones is either over-temperature or under-temperature. The beeping and flashing light on the right side indicate an error or warning. The left side flashing on and off may mean that it is trying to regulate the temperature in that zone.
Unfortunately, it is not possible to shut off just one side of a dual zone wine cooler. The best course of action is to address the issue that is causing the beeping and flashing light. Here are a few steps you can take:
- Check the temperature: Make sure that the temperature in both zones is within the desired range. If the temperature is too high or too low, adjust it as needed.
- Clean the condenser: Make sure that the condenser is clean and free of dust and debris. A dirty condenser can cause the wine cooler to overheat and trigger an error.
- Check the door seal: Check the door seal on both zones to make sure it is tight and free of damage. If the door seal is damaged or not tight, it could be allowing warm air into the wine cooler and affecting the temperature.
- Check the fan: Check the fan to make sure it is working properly. If the fan is not working, it could be causing the wine cooler to overheat and trigger an error.
If these steps don't resolve the issue, it's possible that there is a problem with the wine cooler's control board or thermostat. In this case, it may be best to consult with a professional for repair.
Remember, it's important to maintain a consistent temperature in your wine cooler to ensure that your wine is stored properly and protected from temperature fluctuations. text me on +233557248347
2/11/2023 12:13:59 AM •
Refrigerators
•
172 views • 0 helpful votes
Defy G91641n side by side door
Sounds like a Display board or Main Control board issue. They are expensive so get proper diagnosis via a service call. Then you get warranty on the parts and the job.
How do I install the flap stay hingr
The installation process of a flap stay hinge may vary depending on the specific model and design of the hinge, but here are some general steps to follow:
- Determine the location where you want to install the flap stay hinge. Make sure that it is the correct size and shape for the flap or door that you are installing it on.
- Mark the location for the hinge on both the flap or door and the frame or support structure that it will be attached to.
- Drill pilot holes in the marked locations. The size of the pilot holes should be slightly smaller than the screws that will be used to attach the hinge.
- Attach the hinge to the flap or door first, using the screws provided. Make sure that the hinge is flush with the edge of the flap or door.
- Hold the flap or door up to the frame or support structure in the desired position, and then attach the other side of the hinge to the frame or support structure using the remaining screws.
- Test the flap or door to ensure that it swings smoothly and is properly aligned.
- Make any necessary adjustments to the position of the hinge or the screws to ensure a proper fit and alignment.
- Once you are satisfied with the position and alignment of the hinge, tighten all the screws securely.
- Test the flap or door again to make sure that it opens and closes smoothly and securely.
It is important to follow the manufacturer's instructions for your specific flap stay hinge model to ensure proper installation and avoid any damage or malfunction.
3/17/2023 9:56:42 PM •
Refrigerators
•
60 views • 0 helpful votes
The Francis Francis X7.1 starts making noise (same as when the coffee is made) as soon as I plug the machine. Then the red triangle starts beeping really fast
The fast beeping noise and red triangle on the Francis Francis X7.1 espresso machine is usually an indicator of an error or problem with the machine. This can be caused by various factors such as a malfunction with the pump or water temperature sensor, a clogged brew head, or a problem with the pressure in the brewing system.
Here are some steps you can try to resolve the issue:
- Check the water level: Ensure that the water tank is filled and that the machine is properly connected to a water source.
- Check the grind: Make sure that the grind size is appropriate for the type of coffee you are making and that the grind is not too fine or too coarse.
- Clean the machine: Clean the brew head, portafilter, and other components of the machine to remove any coffee oils or residue that may be clogging the system.
- Check the pressure: Ensure that the machine is properly pressurized and that the pressure gauge is functioning correctly.
- Reset the machine: Unplug the machine and wait for a few minutes before plugging it back in. This will reset the machine and may resolve the issue.
If the problem persists, you may need to contact the manufacturer for further assistance or to have the machine serviced by a professional.
2/12/2023 3:30:27 PM •
Refrigerators
•
138 views • 0 helpful votes
How to fix home labs countertop ice maker not making ice
- Check the condenser coils: If the condenser coils are dirty, it can prevent the ice maker from freezing properly. Clean the condenser coils with a vacuum cleaner or a coil brush.
- Check the ice tray: If the ice tray is damaged or not in the correct position, it may prevent the ice maker from freezing the water. Check the ice tray for any damage and ensure that it is properly seated in the ice maker.
- Check the compressor: If the compressor is not functioning properly, it can prevent the ice maker from freezing the water. If you suspect that the compressor is the problem, you may need to call a professional to diagnose and repair the issue.
3/26/2023 11:37:48 PM •
Refrigerators
•
47 views • 0 helpful votes
Recently installed a new water filter now displaying code EP not making ice
The "EP" error code on your refrigerator's display typically indicates a problem with the water pressure entering the ice maker. This can be caused by a few different issues, including:
- Clogged water filter: If the water filter is clogged, it can reduce the water pressure entering the ice maker, causing the EP error code. Try replacing the water filter with a new one.
- Restricted water supply line: If the water supply line is kinked or otherwise restricted, it can reduce the water pressure and cause the EP error code. Check the water supply line to make sure it is free of any kinks or restrictions.
- Low water pressure: If the water pressure to your home is low, it can cause the EP error code. Check with your local water provider to see if there are any known issues with low water pressure in your area.
- Ice maker valve: The water inlet valve that supplies water to the ice maker may be faulty. If the valve is not opening or closing properly, it can cause the EP error code. You may need to have the valve replaced by a professional.
If you are unable to resolve the issue on your own, it may be best to contact a professional appliance repair service for assistance.
2/12/2023 5:15:04 PM •
Refrigerators
•
127 views • 0 helpful votes
Why is my drip pan over flowing onto my floor after hooking up the water line.
All questions need FULL 'make model (what it is) as first 3 words.
Is it new? Call the vendor as it is under warranty and their task is to leave you with a working machine.
Or is it an old machine and you have only just connected water to it, the most likely reason is dry seals or a sticking eater inlet valve. You will need a service call for that.
Can i get a user manual for mishto 165 litre fridge freezer
It sounds like there may be an issue with the power amp section of your amplifier. When the distortion gets deep and saturated, it could be drawing too much current and causing the amp to shut down to protect itself. This could be due to a number of reasons, including a faulty power amplifier IC, bad solder joints, or a power supply issue.
You mentioned that you suspect the IC may be getting hot. If that's the case, it's possible that it's overheating and shutting down the amp. You may want to try cooling the IC with a small fan or heatsink to see if that helps. If it does, you may need to replace the IC or look into other cooling solutions.
It's also possible that there are bad solder joints or other issues with the power amp section that are causing the problem. If you're comfortable with electronics repair, you may want to open up the amp and take a look inside to see if there are any obvious issues. Otherwise, it may be best to take the amp to a professional for repair.
2/26/2023 8:43:52 AM •
Refrigerators
•
82 views • 0 helpful votes
Not finding what you are looking for?