Most washers has service manual for technicians inside outer housing shell ,just remove top or front or back panel depend on models and retrieve service manual for technicians and follow the service instruction exactly on the service manual and hope fully if you folow the instruction you will be able to reset your washer
Check out the drain hose and connection hose to pump and then check out the pump in the washer for any clog or junk stock in the pump and clean it with warm water and test it is working properly or replace if it is not and reinstall the pump
In the most front load washer this is very common problem and in these new washers such problems are due to malfunction on the door lock or control panel or control board ,you have to check them all one by one
As you should know most bearing comes with instruction how to install bearings and some you could find instructions on line .
Most likely you need to use special tools or bearing installation and removal tools .
Most likely you could buy them from appliance parts stores or auto parts and major tool stores or online tool stores stores and as you should know there are many different size and shape of bearing tools.
You have to be sure what kind bearing tools exactly you need
Be sure not to damage the bearing and drum when installing and removing old one and installing the new bearing
Change of bearing is a little advance project and over whelming for beginners.
Most bearing comes with instruction how to install bearings and some you could find instructions on line .
Most likely you need to use special tools or bearing installation tools .
Most likely you could buy them from appliance parts stores or auto parts and major tool stores or online tool stores stores and as you should know there are many different size and shape of bearing tools.
You have to be sure what kind bearing tools exactly you need
hi i think you mean a ball looks like a ping pong ball it doesent go in pump it sits in filter i allways take them out anyway its up to you strange about water check wires to valves were water pipes fit unplug 1st
Hotpoint Aquarius WF210 Front Load Washer Leaking
This video will show you how to find that leak on any front
loading washing machine
Please remember to subscribe to our YouTube channel for all appliance tutorials
a 4 THUMBS rating is appreciated for answering your FREE question.
And don't forget to like us on facebook
Hi it could be your door lock switch your machine on and wait for 6 seconds and try to open the door if you can thats your problem or may be that the door catch ic worn try and push the door shut with a bit more force
Hi it will have a impact on your washer in time because the pump will block up causing you problems the recommended hight is 2ft 6 ins short term it will be ok
Hi if you let me know what make & model washer you have I will let you know if its a easy fix or not some paddles you can fit yourself easy some you should not try
if your washer drain hose is connected to your sink waste it may be blocked there allso you should check the pump filter may be blocked these 2 things are very common faults as what you have discribed
sounds like your motor brushes have gone depending on what make of washing machine you have I cant help you futher it is difficult to solve without make or model
Certianly most if not all of it!
I suspect that it is the conditioner/softener tray which needs a thorough clean, paying particular attention to the sentences in BOLD ;-0)
-------------------------------------
Remove the complete drawer. To do this you will have to do one of the following-
Top catch-
push down the lip/catch at the middle rear and pull the drawer out (that's how our Bosch one is removed)
release the catches underneath (our daughter's Indesit) or
lift upwards on the tray as it is coming out to clear the lip underneath.
Once out identify which tray is for the conditioner- the others are simply 'chutes' and open-ended.
It will normally have some sort of cover over it which you must remove to expose the little stuck up pipe/tube. On some models there is just a small individual cap over the tube. The tube is down which the conditioner and water should siphon. It is likely to be blocked by 'gunge'- a mix of powder and conditioner. The whole of the tray, particularly this pipe and the bit which fits over it, must be completely clean and clear for it to operate correctly. It is worthwhile checking fairly regularly.
If this has assisted you please consider a 4 thumbs up for the rating.
Thanks and good luck!
John C