Hotpoint Aquarius WF220 Front Load Washer - Answered Questions & Fixed issues
Door locked not open by hand
hi take top off door works on water presure normally clipped to side at top you will see a round or oval part with wires plugged in look at bottom of that there is a clear tube take it off by sqeezing clip pull off open door and put it back or else machine will just keep filling try back soap tray
2/17/2014 1:21:43 AM •
Hotpoint...
•
Answered
on Feb 17, 2014
•
42 views
Bearings drum
Replace the bearings.... the only solution the machine will have a new lease on life.
5/28/2013 11:41:25 AM •
Hotpoint...
•
Answered
on May 28, 2013
•
36 views
Hotpoint wf220 glass door
undo door hinge from cabinet - held with two screws.
the door halves are held togethet with a few screws which undo and the door will split apart so you can replace the glass
5/22/2013 5:22:47 PM •
Hotpoint...
•
Answered
on May 22, 2013
•
180 views
Rattling drum spin
sounds like the spider and drum bearing are on there way out
9/30/2012 6:53:41 PM •
Hotpoint...
•
Answered
on Sep 30, 2012
•
43 views
Hi, the machine/drum area keeps
Things to do make sure despencer draw is clean and the rubber door seal is clean do a maintenance cycle every year this is the hottest wash cycle with cleaning detergent. also leaving the door open after cycle will help hope this helps
1/5/2012 11:01:35 PM •
Hotpoint...
•
Answered
on Jan 05, 2012
•
139 views
Horible smell comingfromthe drum, took the filter
For the pump try taking filter back out and putting back again for smell clean out the rubber door seal with soapy water after the door seal is clean clean the despencer draw fully by taking it out. When you washed the seal and draw get washing machine clean for local super market and do a 95oc wash it should smell nice now if not could be drains hope this helps.
1/5/2012 10:59:11 PM •
Hotpoint...
•
Answered
on Jan 05, 2012
•
177 views
My machine displays F-07 what does that mean ?
- F07 - Heater relay stuck
- This means your heating system has gone wrong you will need to book repair but you could try and reset machine turn off at plug for 5 mins and try again.
- hope this helps
1/5/2012 10:47:36 PM •
Hotpoint...
•
Answered
on Jan 05, 2012
•
99 views
F-04 keeps appearing on the display what does it
- F04 - Pressure switch jammed on empty
- This might need a repair you could try purring off machine at plug for 5 mins and switching back on if still does it you should book repair hope this helps
1/5/2012 10:42:27 PM •
Hotpoint...
•
Answered
on Jan 05, 2012
•
56 views
Door takes to long to open
This is usually the door interlock wearing out, and not returning to normal quickly enough after spinning. Search on YOUTUBE for videos of how to replace one, it usually requires the door gasket to be un-clipped from the outer front panel area (behind the door). There are a lot of parts suppliers here if you need help:
http://www.letsfixit.co.uk/html/appliance_spares.html or
HERE for a good video. Hope this helps, TD.
10/5/2011 10:09:17 PM •
Hotpoint...
•
Answered
on Oct 05, 2011
•
41 views
My hotpoint wf541 shows the on/off switch as on
Please check the power to the mains controller unit and if present please check if the door switch is contacting to give the OK signal for the controller to start the function . So if the inlet does not open and allow water into then is seems that the program controller unit is a suspect.
recheck once again to confirm, try to swap a similar board to confirm and then replace.
9/13/2011 10:58:33 AM •
Hotpoint...
•
Answered
on Sep 13, 2011
•
182 views
Not finding what you are looking for?