20 Most Recent Hotpoint Aquarius WF220 Front Load Washer - Page 7 Questions & Answers


Be sure the lint filter is clean, and the temp sensor blown clean. Sometimes when cleaning the lint filter the some small amount of lint drops by the filter or screen and land on a hot spot. Lint can catch fire so clean with a air hose or vacuum cleaner - Good luck and be safe

Hotpoint... | Answered on Oct 16, 2009


there is a fault in ur machine best thing to do cheak the motherbord for any burn marks, cheak the pump or call an engineer
hope this helps :)

Hotpoint... | Answered on Oct 14, 2009


If it works fine with the heater off then i would say that fault appears to be element..the readings you get seem okay, put you meter onto megs and check, with wires off if you get electrical leakage between live and earth...Body....of element, it could be element is heating with no water in machine causing it to burn out..this is a problem with this machine...Wish you well

Hotpoint... | Answered on Oct 07, 2009


If there is water in it clean out filter,,located within Sump hose

Hotpoint... | Answered on Oct 06, 2009


While turning the motor by hand, I applied medium heat and high fan with a hairdryer. Strange remedy, but it worked, and all is back to normal.

Hotpoint... | Answered on Oct 01, 2009


hi take the top of the machine and check the brick at top or bottom of the machine they sometimes come lose .

Hotpoint... | Answered on Sep 30, 2009


Remove rear cover of washer, and top cover also, tilt washer towards you, get someone to hold washer steady, fit belt round motor pulley,and slowly feed belt round drum pulley, watch your fingers, keep feeding belt round oulley, turning drum at same time, it will be tight, but persist, and belt will go on.
Please rate my solution.
Thanks.

Hotpoint... | Answered on Sep 28, 2009


Its not impossible but a real battle without the correct tools. If at the back of your washer, you have the main arm assembly, then firstly remove the belt and then the pulley.Undo the nuts holding the assembly and in short, pull that assembly off by pulling it towards yourself. Once off, you will see the bearings and seal that need to be replaced. Once done, reassemble carefully and god luck.

Hotpoint... | Answered on Sep 23, 2009


sounds like its in eng test mode un plug 4 an 1hour

Hotpoint... | Answered on Sep 14, 2009


lift lid of top reach to front and pull the wire cable up to the door latch make sure u unplug machine first

Hotpoint... | Answered on Sep 07, 2009


yes the ball should be in there,but shouldnt cause you any major problems if removed.

Hotpoint... | Answered on Aug 05, 2009


Hi, A bleach based cleaner should improve things. It sounds like its a form of mildew , an airbourne fungus that likes damp places. Once bleached it should stay clear for a while. Make sure you rinse it after to avoid damaging your clothes. Hope this helps, Nick.

Hotpoint... | Answered on Jun 22, 2009


no take the sump hose off from the tub off the machine and check for blockages the machine wont spin unless it can drain the water out

Hotpoint... | Answered on Jun 09, 2009


sounds as if the drum bearings have gave way was it noisey b4 this

Hotpoint... | Answered on Jun 09, 2009


sounds like something is jamming the pump, strip pump down and clean

Hotpoint... | Answered on May 28, 2009


can you hear the motor spinning.

Hotpoint... | Answered on May 13, 2009


Please follow the step by step instructions below.....
 
 
1)  Turn off water. Disconnect electrical supply and water hoses.
2)  Remove agitator and cap from machine ( this is not always possible as the agitator gets frozen on the shaft, it just makes the job a little easier )
3)  Lay machine on it's front. Protect front of the unit from scratches. Do not leave it over night on it's front as some oil will leak out the breather hole on top of the transmission.
4)  Remove rear service panel
5)  Loosen both nuts holding the motor mounting bracket in the slotted base plate holes. (see figure 1)
for more details further click the link directly 
http://www.applianceaid.com/beltdrive-change.html





Hotpoint... | Answered on May 07, 2009


filter blocked or brawire or similiar in drain pump take off cover at bottom rear. take of hose going to bottom of tub. filter is in that hose you will have water everywhere. one way round that is to lay machine on side - left side down viewed from rear

Hotpoint... | Answered on Feb 24, 2009


its a matter of removing the front retaining wire and the inner one which holds it onto the drum, an easy enough job to get off, sometimes a pain to get the inner off and on depending whether it s the screw or clamp type , screw=easy. to get the clamp off use a screwdriver to wiggle the bent wire out of the ratchet grooves. to put back is done with long nose pliers, preferably bent nose ones.

Hotpoint... | Answered on Feb 03, 2009


Hello.
I can help you with your query.
In your browser bar type in hotpoint user manuals
In the drop down list, click on
manuals-user guides-handbooks-hotpoint service
In the search box enter your model number and download the instructions.
Please rate my fixya solution.
Thankyou

Hotpoint... | Answered on Jan 29, 2009

Not finding what you are looking for?
Hotpoint Aquarius WF220 Front Load Washer Logo

202 questions posted

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

vince

Level 3 Expert

1234 Answers

gbob59

Level 3 Expert

3042 Answers

James Hehling
James Hehling

Level 1 Expert

11 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Hotpoint Washing Machines

  • Hotpoint Washing Machines

Most Popular Question

start pause switch washing machine not

  • Washing Machines
Loading...