20 Most Recent
Hotpoint Aquarius WF220 Front Load Washer - Page 2 Questions & Answers
Hi, the machine/drum area keeps
Things to do make sure despencer draw is clean and the rubber door seal is clean do a maintenance cycle every year this is the hottest wash cycle with cleaning detergent. also leaving the door open after cycle will help hope this helps
1/5/2012 11:01:35 PM •
Hotpoint...
•
Answered
on Jan 05, 2012
Horible smell comingfromthe drum, took the filter
For the pump try taking filter back out and putting back again for smell clean out the rubber door seal with soapy water after the door seal is clean clean the despencer draw fully by taking it out. When you washed the seal and draw get washing machine clean for local super market and do a 95oc wash it should smell nice now if not could be drains hope this helps.
1/5/2012 10:59:11 PM •
Hotpoint...
•
Answered
on Jan 05, 2012
My machine displays F-07 what does that mean ?
- F07 - Heater relay stuck
- This means your heating system has gone wrong you will need to book repair but you could try and reset machine turn off at plug for 5 mins and try again.
- hope this helps
1/5/2012 10:47:36 PM •
Hotpoint...
•
Answered
on Jan 05, 2012
F-04 keeps appearing on the display what does it
- F04 - Pressure switch jammed on empty
- This might need a repair you could try purring off machine at plug for 5 mins and switching back on if still does it you should book repair hope this helps
1/5/2012 10:42:27 PM •
Hotpoint...
•
Answered
on Jan 05, 2012
Door takes to long to open
This is usually the door interlock wearing out, and not returning to normal quickly enough after spinning. Search on YOUTUBE for videos of how to replace one, it usually requires the door gasket to be un-clipped from the outer front panel area (behind the door). There are a lot of parts suppliers here if you need help:
http://www.letsfixit.co.uk/html/appliance_spares.html or
HERE for a good video. Hope this helps, TD.
10/5/2011 10:09:17 PM •
Hotpoint...
•
Answered
on Oct 05, 2011
My hotpoint wf541 shows the on/off switch as on
Please check the power to the mains controller unit and if present please check if the door switch is contacting to give the OK signal for the controller to start the function . So if the inlet does not open and allow water into then is seems that the program controller unit is a suspect.
recheck once again to confirm, try to swap a similar board to confirm and then replace.
9/13/2011 10:58:33 AM •
Hotpoint...
•
Answered
on Sep 13, 2011
Does not complete the cycle
Hi,
Problems with a washing machine not spinning or not draining are often interrelated..
If you are having a problem with your top load washer then check out thistip...
Washing Machine does not Pump or Spin
If you are having problems with your front load washing machine then checkoutthis tip...
Front Load Washing machine not draining and or not spinning
heatman101
';
;'
';
8/13/2011 7:41:52 PM •
Hotpoint...
•
Answered
on Aug 13, 2011
Something has got between the drum and its
I would enter via the sump hole ....Remove the hose 1st then you may be able to grab it failing this remove heater element and you will see it to remove...Good luck
3/24/2011 4:05:25 PM •
Hotpoint...
•
Answered
on Mar 24, 2011
Washer won't drain
You need to clear out the drain pump. if you should be able to access the pump from the front bottom by unscrewing and removing the filter. If not then you will need to tilt the machine back as far as you can so you can access the underneath. You will see the small drain pump. Have a basin ready to catch any water that comes out when remove the pump which is only held in by 1 or 2 screws and twisted out or pulled out. If it is clear then try removing the pipe that goes from the pump to the base of the tub. Hope this helps
3/16/2011 2:03:12 PM •
Hotpoint...
•
Answered
on Mar 16, 2011
Not finding what you are looking for?