20 Most Recent
Hotpoint Ultima WD72 Front Load Washer/Dryer - Page 7 Questions & Answers
Hotpoint Ultima WDM73
The whole tub has to come out then split,it is worth changing bearings at same time.Parts can be supplied by us.
Hotpoint washer dryer
1. Turn off power
2. Turn off hot and cold inlets if possible - if not then pop outside and turn off water to house
3. Unscrew all the screws on the back of the machine to take off the rear panel
4. Use a large pair of pliers to remove the clip securing the large black rubber hose to the drum chamber.
5. Remove sock. Trust me, it's a sock :)
6. Put it back together.
If there is no sock (but I'm sure there is) then work your way through the drainage system until you find the problem. I once had a label from a baby grow in the fan blades of the pump. The drainage is pretty self explanatory. There's only the internal black hose with a filter in, then the pump, then the external hose. If there really is no sock then check them all.
Hotpoint ultima 1200 wm72
code e30 means motor fault. this can be just motor brushes, tacho fault or module fault. can't narrow it down more than this - you will have to dive in and check
Hotpoint ultima extra washer dryer WDM73
i found this manual,if you know what your problem is this might show how to change the faulty bit. I dont know what machine this is but they all seem pretty simular, i used this to change my door lock.
MACHINE NOT EMPTYING
Most newer machines and a lot of older ones have a removable filter on the front of the machine. Some have a small hinged door others you have to remove the bottom trim on the machine to access it. Once you have screwed out the filter and removed it you can usually see the impellor which is a cross shaped plastic piece about 2 inch's across and down. Check to see if it moves freely or if there's something jamming it.Only other way is to remove the pump from it's housing, it's usually held in by 3 screws, sometimes phillips sometimes torx head screws. Once you've removed the screws the motor will just pull off. You can usually do this by just leaning the machine back so you can get at the under side of it. Be sure when you refit the pump it goes back in the same position and that the rubber o ring locates properly..
Hotpoint washer dryer ultima 1200 model WD71S
most like cause is the door interlock is faulty but its one of those jobs that unless you have the right equiptment namely a tester you won't know for sure unless you change it. Could also be the voltage from the control board is't correct so best let someone who knows check it for you.
Hotpoint washer dryer leaking water whilst drying
driers work by running cold water down the back plate of the machine so the hot damp air condence's on to it. It works on the same principle as your bathroom mirror, because its colder than the air around it the moistier in the air condence's on to it. Most machines use a seperate inlet valve from the cold water to do this, they are proned to rub against the back of the drum.Take the top cover off the machine and check the hose's from the cold inlet onto the back of the machine you'll probably find a hole worn in it.
Not emptying
what that signals is the impellor on the end of the pump is jammed or loose. Check to make sure it is free.
Shakes violently and bangs on spin
transit bolts not removed. also can be caused by motor not winding up gradually into spin - usually a motor tach fault. most likely cause is transit bolts
Wiring
I'm no expert but currently have the lid off my machine. Roughly where did you find the disconnected wire? I assume as you replaced the belt, it is at the back of the machine? There are a couple of male spade connections just above the water pipe inlets where I can see a brown and white wire? Does your wire have a female spade connection?
Soap
As you look at the despenser drawer it has 3 chambers. The left chamber is for Prewash detergent, middle for Fabric conditioner, right is for Liquid or powder detergent. Or use a plastic ball in the main drum!
Washine Machine pump
Sounds like a pressure switch tube may be blocked or switch may be faulty. Is there a switch on your machine? If so try pulling the tube off at the bottom of the switch and blowing through it to clear the blockage. (If you take the top lid off you should see a diaphram operated switch with a small bore plastic tube going from it to the bottom of the machine)
Hotpoint Ultima WT965 - Water gushing out from door and soap drawer
you have a blocked filter, unplug from mains, take off back panel you will see a black sump hose coming from the tub to the pump, tilt the machine forward and put a dish or bowl under sump unscrew clamp and pull off slowly to release any water in the drum. You will find a blockage, also what appears to be a ping pong ball dont throw away it is meant to be there.
Washer not working
i had this and the timer circuit was faulty i found a few dry solder joints. i re soldered it and cured the problem.
Error E15 - MAchine not draining
drain is same wehatever the program. filter is likely blocked. access is not that easy. take off panel at bottom rear. filter is in pipe from bottom of tub to pump. undo this pipe, take out filter. you may have water everywhere so be carefull
Not finding what you are looking for?