Hotpoint Aquarius WD640 Front Load Washer/Dryer - Page 3 - Answered Questions & Fixed issues
THIS MESSAGE COMES UP ON THE DISPLAY
See my other reply to your request. It took me less than 2 secs on a search of your listed model to find a manual. One thing it says in the troubleshooting section is that if it fails to start with something showing on the display is to press and hold the start button for at least 3 seconds and the machine should start. See imagebank.indesitcompany.co.uk/brochures_online
8/29/2014 12:43:40 PM •
Hotpoint...
•
Answered
on Aug 29, 2014
•
50 views
This message comes up on the display how do i remove it please
Where is your user handbook? If you don't have one go online to the OEM who have most current models available for free download. If not get the model and serial number and search online. Call a local appliance agent for your brand, if they have a repair facility they may have a man who know's?
8/29/2014 12:36:11 PM •
Hotpoint...
•
Answered
on Aug 29, 2014
•
58 views
Where is the drain filter?
turn machine on its side under neath you will see metal clamp undo this and filter or area were large coins will fall and stay will open
have cloths ready for some water spillage
8/6/2014 8:35:22 AM •
Hotpoint...
•
Answered
on Aug 06, 2014
•
42 views
How do I get the clips off a washing machine filter?
The clip secures the SUMP HOSE which has the filter in it ,Put an old towel under this and give it a tap with a flat bladed screwdriver this will loosen the White clips that hold on the hose,then you remove filter and clean noting which way it came out , refit
5/8/2014 5:40:30 PM •
Hotpoint...
•
Answered
on May 08, 2014
•
69 views
Drum not turning
check the motor brushes after taking out the plug
3/14/2014 10:41:32 PM •
Hotpoint...
•
Answered
on Mar 14, 2014
•
53 views
F11 code
is the filter clean
3/14/2014 10:38:54 PM •
Hotpoint...
•
Answered
on Mar 14, 2014
•
62 views
Wd640p combination dryer
Same happened me - the drier heater circuit has a safety cut-out (160°C, Red Spot) which does not reset, the component must be replaced. It is not a simple DIY task as it is fitted from the INSIDE of the air heater duct.
In my case, there were signs of burnt fluff in the duct. I suspect that fluff was sucked into the duct by the fan, dried out, burned and tripped the safety cut-out.
1/14/2014 9:25:39 AM •
Hotpoint...
•
Answered
on Jan 14, 2014
•
172 views
Replacing bushes hotpoint wdf740
check the length of the motor brushes.
new are about 30mm long.
should also clean up the motor with compressed air.
Remove the electronic module also do a cleanup in all contacts of connectors. If necessary wash with isopropyl alcohol which can be purchased at a pharmacy.
Dry with a hair dryer.
Do not forget to make reset to clear the error.
(Pressing the start button until all the LEDs light up)
12/22/2013 12:05:08 PM •
Hotpoint...
•
Answered
on Dec 22, 2013
•
326 views
Where is the dryer fuse,located on an aquarius
-There is not fuse. But there are thermal fuse (Possibly 3)
-Disconnect main power and open back panel cover. You'll see it.
-Possibly heater element burn out.
Good Luck
Mai
12/21/2013 2:00:24 AM •
Hotpoint...
•
Answered
on Dec 21, 2013
•
83 views
Not finding what you are looking for?