Hotpoint Aquarius WD63 Front Load Washer/Dryer - Page 6 - Answered Questions & Fixed issues
My machine has the door lock light on and wont
Hi,
Remove the top cover, and release the door catch from inside the washer, you will probably need a screwdriver or similar to do do this.You will need to replace the door catch and spring, and possibly the door lock, as it may break when you force the door open.
Thank you !!
6/26/2010 2:35:17 PM •
Hotpoint...
•
Answered
on Jun 26, 2010
•
194 views
WD440 HOTPOINT AQUARIUS LEAKING FROM FRONT/NOT DRYING
Power off the mains. The
filter is located behind the silver plate at the back of the machine at
the
bottom. Four screws hold it on. Drain
out all the water. The filter is inside
the big black rubber hose attached between the pump and the main drum.
Remove
the plastic clip holding it to the pump unit and then the metal cir clip
holding it to the main drum. Inside is a white molded cone and a big
white ball
which floats. You will find a lot of junk here, clean out thoroughly. To
refit
put white cone back inside just as you found it, at the bottom, fit ball
back
into the cone. Attach to the bottom to the drum and re-fasten the cir
clip.
Finally reconnect the gator to the pump unit and tighten the plastic
clip. Check out the pump too before reconnecting.
The leak in the front could be from one of the tubes bringing water to the detergent box; you should open up top to locate.
And rate me nice pl for the
free help!
6/8/2010 5:42:16 AM •
Hotpoint...
•
Answered
on Jun 08, 2010
•
922 views
Wf310 hotpoint aquarius washing machine wont spin or drain
Power off the mains. The
filter is located behind the silver plate at the back of the machine at
the
bottom. Four screws hold it on. Drain
out all the water. The filter is inside
the big black rubber hose attached between the pump and the main drum.
Remove
the plastic clip holding it to the pump unit and then the metal cir clip
holding it to the main drum. Inside is a white molded cone and a big
white ball
which floats. You will find a lot of junk here, clean out thoroughly. To
refit
put white cone back inside just as you found it, at the bottom, fit ball
back
into the cone. Attach to the bottom to the drum and re-fasten the cir
clip.
Finally reconnect the gator to the pump unit and tighten the plastic
clip. Check out the pump too before reconnecting.
And rate me nice pl for the
free help!
6/8/2010 5:36:50 AM •
Hotpoint...
•
Answered
on Jun 08, 2010
•
1,547 views
Water remains in the tub after spin cycle
Sounds to me like the Water Pump is bad. Hopefully if your machine is less than a year old you can get it fixed for free, if you bought it new it will have a 12 month warranty on it. If not you can always buy the manual for your washer and try to fix it yourself.
5/15/2010 4:31:08 PM •
Hotpoint...
•
Answered
on May 15, 2010
•
146 views
Hotpoint aquarius wf740
Sounds like water pressure could be low or inlet pipe is kinked.
F04: possible filling or water level problem. Check water inlet pipe (or shut-off valve), or the outlet pipe, or the pump or pump filter if accessible (check for blockages or foreign objects). Also could be the water valve solenoid weak, causing filling to be too slow.
F05: possible draining (pumping off) problem, check the pump filter, or pump, outlet pipe, or U-BEND.
Don't forget to rate!
5/3/2010 7:39:56 AM •
Hotpoint...
•
Answered
on May 03, 2010
•
557 views
How can I unscrew the drain outlet at the bottom
Keep trying to unscrew it, as it should come right out for cleaning. A little water will come out too so put a small tray under the machine first.
Look at my other solutions, as for DOOR light flashing.
4/4/2010 8:32:07 PM •
Hotpoint...
•
Answered
on Apr 04, 2010
•
490 views
Hotpoint Washing Machine (W540) stopped working, LEDs flash....?
You must get the filter out, as there is a very good chance that this is the prob, keep unscrewing it and try to move it about, then screw it back in again , and then out again, hopefully this will dislodge whatever it is that is holding the filtter in.
Plz rate thiese comments.
Thanks.
4/2/2010 11:59:28 AM •
Hotpoint...
•
Answered
on Apr 02, 2010
•
307 views
Stay in high flats 4up low water pressure is there
If your water pressure is to high or even to low then just check the taps at back where hoses are fitted. Make sure they are fully open if pressure is to low, also make sure there are no kinks jn the pipes. If pressure is to high then just turn taps down a little.
3/12/2010 9:53:24 PM •
Hotpoint...
•
Answered
on Mar 12, 2010
•
94 views
Not finding what you are looking for?