Hotpoint WMA40 Front Load Washer - Page 7 - Answered Questions & Fixed issues
General Electric Hotpoint HTWP1400FWW White 27.
The washer only fills to half on the rinse cycle.
Ideas?
https://www.google.com/search?sxsrf=ACYBGNT6nLbuauU5ZByczrMC6cLaGIk6AQ%3A1581870161107&source=hp&ei=UWxJXtzCBND4aILKh_gH&q=General+Electric+Hotpoint+HTWP1400FWW+White+27.+The+washer+only+fills+to+half+on+the+rinse+cycle.+Ideas%3F&oq=General+Electric+Hotpoint+HTWP1400FWW+White+27.+The+washer+only+fills+to+half+on+the+rinse+cycle.+Ideas%3F&gs_l=psy-ab.3...223788.223788..226888...2.0..0.0.0.......1....2j1..gws-wiz.TGW-acS8eao&ved=0ahUKEwicr6DIvdbnAhVQPBoKHQLlAX8Q4dUDCAU&uact=5#kpvalbx=_n3NJXvmnM8GelwTnwpGQBQ28
What does f05 mean on a hotpoint washing machine
f-05 usually relates to either the pump being blocked or the sump of this particular model being full of coins, color catchers etc. first keep it simple, ensure outlet hose is not blocked or kinked....but if not follow these steps
- To sort this isolate from mains
- take off back inspection panel.
- tilt machine forward- get sum1 to hold it for u.
- The sump is the black hose attached to drum.
- place a basin under this and loosen jublie clamp using star head screw driver/ 8mm socket,
- pull sump downwards and remove any blockage.
- note the plastic ball is part of the sump assembley.
- refitt the sump again and tighten clamp, pull down firmly on sump to ensure fitted correctly
if there was nothing in the sump it is sumthing jamming the pump, hairgrip, nail, etc.tilt machine forward as above with a basin ensuring isolated from mains power
- pump is attached to other end of sump hose, right side of machine as you look in the back.
- using flat screwdriver lift plastic tag up and slide pump assembley to the left releasing it from base of machine
- clip of plastic cover from top of pump
- remove wires from pump
- u should now be able to turn pump around so u can see 3 hex head screws
- remove screws taking note of the position of pump
- remove pump and clear blockage
- reverse steps to reassemble
if this does not sort it poss a new pump needed
Door sign flashing and keeps clicking - Hotpoint Aquarius WMF720
It seems that the door cannot be locked.
Check that the door closes correctly and you hear the click when it closes. If this is ok and you cannot start any cycle but continue hear clicking, then you have a problem with the door lock latch and needs to be replaced. Here is a video of how you can do it after you buy the spare part, according to the model and serial number of your appliance. The video is for a different brand of washer but don't worry the process is exactly the same!
If you think you can't fix it your own, you should call an engineer..
Washer Door Lock Assembly part 131763202 How To Replace
What can cause element and fan not to work in a electric double oven red light is on top oven fine main oven dead
Most likely the main oven element has blown. A new element will cost about £20-£40, and if you're reasonably competent you can swap it in around 15 minutes. Turn the power off, undo the screws holding the element and pull it out. Carefully disconnect the push on terminals and take the element out. You probably won't even need to test the element with a multimeter, as you'll easily see if it's blown as the insulation will have blown off. nb. You may have to remove a cover before you can get at the element but should only be 4 screws max. Refitting is reversal of removal, just make sure the wires don't fall back behind the oven casing before you reconnect them!
Not finding what you are looking for?