20 Most Recent
Hotpoint TDC32 Electric Dryer - Page 9 Questions & Answers
I have just replaced a
There is no circuit breaker in this dryer as such.
Establish that you have got power to the m/c, if you have, then could be faulty door switch, or you may have inadvertantly pulled a wire off somswhere.
Try the dryer in another socket and make sure you know that the fuse is a good one.
Hot Point Dryer does not
Feel the outer cover at rear of the dryer at the bottom,if it starts to feel warm then the heater is working, the buzzing noise could be the motor trying to start, or noise from the relay, if the heater does not come on then could be timer faulty or faulty start relay. It is a a process of elmination.
I have a Heavy Duty
Could be a dry rear drum bearing, if it has a removable rear panel, unscrew it and spray the end of the drum shaft and bearing with Wd40 or similar.
Please rate this solution
Dryer element not working
If the water light is on and you have wasted money on a heater it's more likely to be a stuck float switch which cuts out the heater.Why don't you get the people who make it to repair it rather than DABBLE and get yourself in a mess??
Drum wnt turn
If the unit is new...get a service person in. Do not do anything yourself.
My dryer
There is something binding and taking your motor out. chances are the motor may have failed. It's called thermal overload. it shuts down as a safety precaution...With ge...the front slide bearing...the white area that the drum rides on is worn out and ....probably the rear drum bear is worn down too...GE is generally expensive to fix...
Hotpoint aquarius ctd40
most likely, there is a blockage in your exhaust. take it apart and check every inch from your dryer to the outdoors. i clean mine once a year, it keeps the dryer running efficiently. when lint backs up in there, the heat cannot get out and there is a sensor that will shut off the heating element when it gets to a certain temp, so your clothes will take a long time to dry
Tdc30 dryer
rthe high temp thermostat is located on the heater box,the low temp thermostat is located on the blower box ans the main fuse is the smaller round one-let me know how you do-mike
No heat in dryer
if you can see your heating element, use a meter to test for continuity. remove the clips or wires attached to the terminals of the heating element and put the probes of the meter.
the reading should be close to short since it is a heater. maybe 1 to 10 ohms.
tnx 4 using fixya,
drcool
Dryer
need more info,does it spin and work at all?let me know-mike
Hotpoint aquarius tdc
DEAR FRIEND,
ngfam1 here for you!
I am happy to be of assistance!
STOP! BEWARE OF FIRE AND OR SHOCK DANGER!
TIME FOR REAL SERVICE .
HUNDREDS OF PEOPLE IN THE USA ARE KILLED OR HAVE THEIR HOUSES BURN DOWN FROM THESE PROBLEMS!
CALL SERVICE.
YOU WORTH MORE THAN THE WASHER!
Here is a good service that I recommend to my customers,
in our 65 year old appliance business! they answer 24/7
Not expensive!
A&E Factory Service
1-800-905-9505 -(IN U.S.A.)
They are open to make appointments 7days/24hours
A&E is factory authorized service for most brands!
Including warranty work!!!
They will help you, and all will be well!
Good luck!
You will be fine now!
Thank You
Bless you,ngfam1
PS. PLEASE GIVE ME A GOOD RATING HERE ON FIXYA.COM BEFORE YOU SIGN OFF!
No heat
replace the thromostats at the rear of machine cost about £18.00 takes about 10 mins. PS after you have done this dont open the drier door before its finished ats hot cycle it is the sudden drop in temp that blos the thermostats,
Hotpoint CDT40P error message
DEAR FRIEND,
ngfam1 here for you!
I am happy to be of assistance!
WHOEVER DIAGNOSED THE PROBLEM DOES NOT HAVE ENOUGH EXPERIENCE!
YOU NEED TO USE FACTORY SERVICE !
OR IF IT IS 10 YEARS OLD OR MORE ,DO NOT WASTE MONEY FIXING IT! THE NEW ONES ARE MUCH MORE EFFICIENT!
Here is a good service that I recommend to my customers,
in our 65 year old appliance business! they answer 24/7
Not expensive!
A&E Factory Service
1-800-905-9505 -(IN U.S.A.)
They are open to make appointments 7days/24hours
A&E is factory authorized service for most brands!
Including warranty work!!!
They will help you, and all will be well!
Good luck!
You will be fine now!
Thank You
Bless you,ngfam1
PS. PLEASE GIVE ME A GOOD RATING HERE ON FIXYA.COM BEFORE YOU SIGN OFF!
No Heat
Try Float chamber behind water container (Where it snaps into), Wet lint may be clogging the micro switch hence simulating a full conatiner leading to no heat output.
Hope this helps
:-)
Not finding what you are looking for?