20 Most Recent Hotpoint NLL113EYWO Electric Dryer - Page 4 Questions & Answers

You are obviously not putting it back right or has something fell down the back

ALWAYS UNPLUG YOUR DRYER BEFORE ATTEMPTING TO DO ANY WORK ON IT.
If you have to replace your drum belt and if you have a front loading machine.

Remove the electrical console that holds the timer switch, start switch, etc. from the top of the dryer. Be real careful not to knock any of the wires off of the timer switch. Then remove the top of the dryer.
Remove the front of the machine, this will expose the belt and drum, remove the drum and belt and this will expose the drum rollers, idler arm bracket with pulley, and motor with pulley. Pay attention to the route of the belt, this will come in handy when you go to reinstall the belt and drum.
Sometimes the belt will slip off of the idler arm or motor causing the drum not to turn.
While you have the drum out, I would recommend that you lubricate the drum rollers at the shaft of the roller with a good grade of machine oil like 3 in One oil. This will save you a problem later with the rollers getting noisy, also check your drum rollers for flat spots, if they have flat spots on them this will cause a noise like a thumping type noise. You will need to replace the drum rollers if they have flat spots on them.
I will include these two websites for parts and further help:
http://www.partselect.com/
http://www.appliancepartspros.com/index.aspx
Both also have chat assistance 24/7.
Good luck,
I hope this helps

the belt may be off/broken, motor bad, or idler assemblage.

Here is a website with the routing of the belt the Hotpoint is( General Electric (GE) - Large Capacity Models 1970-1990):

http://forum.appliancepartspros.com/dryer-repair/25860-dryer-belt-diagrams.html



how to replace the belt:

http://www.ehow.com/how_6100255_replace-hotpoint-dryer-belt.html

images for Hotpoint tcym 750c tumble dryer wiring

Hotpoint TCYM 750C Style - YouTube

? 3:07 https://www.youtube.com/watch?v=RjQMN6U4PdE Oct 8, 2012 - Uploaded by Missing Sleep Hotpoint TCYM 750C Style. Missing Sleep ... How to replacetumble dryer belt Hotpoint, Indesit, Ariston, Creda, Proline etc - Duration: 9:36. by ...

Hotpoint tcym 750c tumble dryer serial number tcym750c6p ...

www.fixya.com/.../t25992053-hotpoint_tcym_750c_tumble_dryer_seria...

48 mins ago - SOURCE: Reconnect wiring on a Hotpoint VTD00 tumble dryer. most electric dryers have a wiring schematic on the back or inside on the back ...

https://www.manualslib.com/manual/600172/Hotpoint-Tcym-750c-Style.html

There should be a wiring diagram inside console where timer and switches are.

The thermostat and element are mounted on the back wall of the dryer. To gain access you must remove the drum. Here is my home movie:My home movie and repair photos for GE hotpoint dryers If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

If it uses a pilot light check to see if it is lit. If no pilot the electric starter is probably bad. If no pilot does it make light buzzing as it is trying to start, if not the starter is bad.

Some thermostats such a cycling thermostat are resettable and automatically cycle on and off based on your temperature setting choices. Others such as a thermal fuse are not resettable and will blow if dryer gets to hot. That type has to be replaced after determining and correcting why it overheated.

Maybe the things you are trying to dry are really soaking and it overloads the machine; have you tried hanging them up first to drip?

Could be fuse / thermostat, improper voltage, timer or control, motor, or wiring.

most switches have the thermostat as part of the switch check that or replace the thermostat

check the exhaust tube externally and internally for excess lint build-up on the sides. You may not have the vent obstructed, but you may have the venting restricted. Clean out lint if there is excess. It may need a good scraping/ brushing to help your machine breathe. Just an extra thought.

http://www.hotpoint.co.uk/hotpoint/_pdf/manuals/19506725800_UK.pdf

check your vent system.hope this helps.

the model number that comes up is DLL2650BPL you could have a bad igniter,gas coils or sensor but the only way to tell is by reading them out with a meter the igniter part number is WE4X444 gas coils are part 5303931775 and the sensor is part WE4X448 you can go here to see parts https://www.repairclinic.com/Shop-For-Parts/a8b95d49280/Model-DLL2650BPL-Hotpoint-Dryer-Parts if you have heat at the beginning and then no heat it will be the gas coils but one of the coils still could be bad and not work at all but check all parts with meter before you start ordering parts you don't want to change out good parts.

call ge they'll know i think it's 1-800-gecares look at the model tag or manual to find number

The THERMAL Switch is detecting values higher than normal. This is to keep your dryer from over heating and causing a fire. This feature is a PROTECTION built into the dryer circuit and indicates you have a bad dryer heater needing replacement. At some point, you may be blowing a circuit breaker which is the second line of defense. Rather than having a FIRE...get a repair man to fix the Dryer NOW!

that isn't a model number,open the door to the dryer,look around the opening where you put the clothes in and send the full model number,