20 Most Recent Hotpoint NVL333EY Electric Dryer - Page 2 Questions & Answers

Since the Hotpoint uses the cheapest switch without a good track record for dependability, that would be my guess.

Hi,
The cycling or operating thermostatis often the problem when a dryer runstoo hot, but there are also other things that can make it run hot also.

Here is a tip that I wrote that gives more details about why a clothes dryer will get too hot.

Clothes Dryergetting too hot

heatman101

Hi tirisa...

ALWAYS UNPLUG YOUR DRYER BEFORE ATTEMPTING TO DO ANY WORK ON IT.
Note: This method works for most front loading machines.
If you have to check/replace/repair your drum motor,drum seals,belt,rollers, etc.
If replacing drum seals be sure to use a good grade of weather proof cement to hold the seal/s in place, some seals are furnished with the cement to glue it in place.
Remove the electrical console that holds the timer switch,start switch, etc. from the top of the dryer if necessary. Be real careful not to knock any of the wires off of the timer switch or other electrical connections.
Remove the lint filter and the two screws that hold the filter housing to the top of the dryer lid.
Then remove the top of the dryer by inserting a screwdriver between the top and frame on each side of the dryer to pop the lid up from the retaining clips.
Note: Some of the tops tilt backwards on a type of hinge and do not have to be removed completly.
Remove the front of the machine by disconnecting the door switch and removing the two screws located on either side of the dryer frame.
Move the door and front of machine forward to remove.
This will expose the belt,idler bracket and drum, remove the drum and belt and this will expose the drum rollers, idler arm bracket with pulley, and motor with pulley. Pay attention to the route of the belt, this will come in handy when you go to reinstall the belt and drum.
Sometimes the belt will slip off of the idler arm or motor causing the drum not to turn.
Note:The way the belt goes back on is, as the belt comes off the drum has to be doubled (pushed together to form a loop) and goes under the idler pulley then to the motor pulley.
Here is a link to see a picture of your belt routing in case the belt is broken when you open your dryer:
http://www.expertappliance.com/dryerbeltconfiguration.html

While you have the drum out, I would recommend that you remove and lubricate the drum rollers.
And also clean the shafts of the rollers as they will collect hair,dust,etc and cause problems and then lubricate the shafts and rollers with a good grade of machine oil like 3 in One oil or a vasoline type of lubricant. This will save you a problem later with the rollers getting dry and making a squeeling noise, also check your drum rollers for flat spots, if they have flat spots on them this will cause a thumping type noise.
You will need to replace the drum rollers if they have flat spots on them.
Please take time to rate me

Could be this or worn jockey pulley bearing at the motor, try a little WD 40 on it to see if it eases....You must make sure there is no play on the drum as this back bearing wears easy....

first row far right, good luck Tim:



http://www.applianceaid.com/images/belt-config.JPG

Hi,

Here is a tip that I wrote about dryers and noises...It will help you determine what is happening there...Dryer Repair Squeaks, Grinding, Clicking and Knocking Noiseheatman101 Asker

Hi,

There can be many reasons why your dryer will not start or turn...

The most common causes are the belt breaking or jumping off, or the motor going bad...

Here are a couple of tips that I wrote will help you to figure out why your dryer will not run...

Dryer Repair - The Dryer is not Turning

Dryer Repair - The dryer will not start


heatman101

Hi,

If you are having problems with your gas dryer not heating the most common problem is that the ignitor goes bad. Even though it glows sometimes it is still not working properly.

if you dryer is gas check out this gas no heat tip....

If you have an electric dryer, you can have many different things that can go wrong causing the dryer not to heat.

check out this electric no heat tip...

heatman101

Unplug it


I have more here If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Are you saying that it is "literally" "burning" the clothes or it just smells like that are brunt? Regardless, if it is doind either, it sounds like there is a problem with the thermostate on the unit. If the unit is only three years old, it is highly unlikely that the unit has the wrong heating element installed within it as this is the only other issue that causes such a problem. If you have the manual for your unit, you can easily find where your thermostate and heating element are located and you can check both...if you are somewhat handy. You can also replace both or either as well as opposed to calling a service person. If all else fails, take the unit to a service person or have them come to you. However, if you are going to attempt repairs, make sure that the unit is UNPLUGGED prior to attempting to work on your unit. SAFETY FIRST! Good luck.

If your dryer is running, turning the clothes, but has no heat, the heating element is bad and needs to be replaced. It is somewhat easy to replace if you are handy. You can usually find one at a hardware or appliance store but you may have to find one on line. Make sure that you UNPLUG the unit prior to working on it. SAFETY FIRST! Good luck.

Hi,

If you are having problems with your gas dryer not heating the most common problem is that the ignitor goes bad. Even though it glows sometimes it is still not working properly.

if you dryer is gas check out this gas no heat tip....

If you have an electric dryer, you can have many different things that can go wrong causing the dryer not to heat.

check out this electric no heat tip...

heatman101
/////////////////////////////////

on the backside of the dryer under an access plate, here is a picture of one that is open:

http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=10&newsdesk_id=5

sounds like a motor these Do not use a starting capacitor, they use very small Gage wire for the start windings ..You can get a new motor for about 130.00 dollars if you decide to replace it I would advise you to also order a new blower wheel ,, after time the blower wheel has a way of seizing its self onto the motor drive shaft and 90% of the time you have to destroy the blower wheel to get it off it adds about 25.00 to 30.00 more to the job but you will be glad you did

you need to change the fan

Hi,

There can be many reasons why your dryer will not start or turn...

The most common causes are the belt breaking or jumping off, or the motor goingbad...

Here are a couple of tips that I wrote will help you to figure out why yourdryer will not run...

Dryer Repair - The Dryer is not Turning

Dryer Repair - The dryer will not start


heatman101

On a low setting the exhaust temperature should average in the 120-125°F range. On medium the temperature should average 130-140°F and on high 140-155°F, depending on the dryers design. Those temperatures should be basically the same with or without clothing.

Hi, If you are having problems with your gas dryer not heatingthe most common problem is that the ignitor goes bad. Even though it glowssometimes it is still not working properly. if you dryer is gas check out this gas no heat tip.... If you have an electric dryer, you can have many differentthings that can go wrong causing the dryer not to heat. check out this electric no heat tip...

heatman101