20 Most Recent Hotpoint NBXR463EBWW Electric Dryer - Page 5 Questions & Answers

Question edited to add Maker. Question moved to Hotpoint. Most dryers have 2 elements, one for low, and one for medium. High heat is both elements together. My guess is that your medium element has failed and you are only getting low heat. Test with a multimeter or call for service. https://www.google.com/search?q=Hotpoint+Ctd+80+P+tumble+dryer+parts ..

No, check for broken drive belt.

It might be the start button not making contact or it could be the control board. It depends on the model, Hotpoint has made a few in the last 50 years. Whip your multimeter out and check the switch for continuity.

make sure correct size then make sure routed correctly if ok check for idler wheel adjustment

Remove top cover, and see if the belt is intact, if it is then it could be the motor is not working for one reason or another, this would entail further investigation.
Please rate my solution.
Thanks.

possible drive motor overheating and turning off if thats ok possible blocked vent and is overheating

It really depends on where it is stuck, and you don't tell us that. If it is down where the filter is, you can get it with a magnet taped to a stick. If it is between the drum and the outer drum you may be able to open out a coat hanger and pull it towards the edge. Depending on the age of the dryer, it might be time for a full strip-down service and do some maintenance. Grease the bearings, oil the drum slides and remove all the lint that hides inside and causes 'Dryer Fires'. You are not alone, and there are videos to help you. https://www.google.com/search?q=remove+bra+wire+from+hotpoint+v3d01 ..

This link has the part that is probably bad: Hotpoint Washing Machine Compatible Door Interlock - Part Number INT51 for bwd129 (ransomspares.co.uk)

Hi, Well if it is getting hot but not drying the clothes than most likely you have an airflow problem. Take off the vent hose on the back of the dryer. It will be plugged up with lint either inside that vent on the dryer or the hose will be plugged somewhere. If you clean this or just plain replace the old hose this will take care of the problem. Good Luck. feed back is appreciated.

This will depend on what has broken. Get a Good technician to look at it and they'll be able to tell you if it's a repair or replace situation. Start by checking the basic stuff first. Does yours use an overflow tank or is plumbed into the main house drain? If it is a tank, check it's empty. Some machines have an electronic safety cut off that trips on when the tank is full. The machine also has a large filter, usually fitted below the drum, That needs to be cleaned regularly. The three main mechanical things that need to be checked will be the motor, the drive belt and the drum bearings. Try this... With the machine Off and empty, try turning the drum by hand. It should turn smoothly with a small amount of resistance. Push the drum up and down. it should only move forward and backwards a small amount. As it turns it should have a quiet 'hiss' like sound. this is the bearing on the back of the drum. If the drum spins very easily it is possibly the drive belt is damaged or snapped. If the drum feels gritty and has a gritty noise as it turns it is possibly the drum bearings. If the drum won't turn or is very tight when it turns this is also a sign of bad bearings.

Possibly a broken/faulty switch I would think.

Brown in the centre https://www.youtube.com/watch?v=6IBnIkoJ1BQ

You will find the thermostats located at the rear of dryer.
Remove cover, and you will see them adjacent to the heater element, change them both, even if only 1 is faulty.
Please rate my solution.
Thankyou.

The thermostat probably needs to be replaced rather than reset.

belt slipping --motor bearing--check warranty if valid notify manufacturer

https://www.searspartsdirect.com/model/599b1eoj0u-001811/hotpoint-htr16absarww-top-mount-refrigerator-parts

Check your duct for blockage

some one help me pls?

Check dryer door switch. Most common failure.

replace condensor