Planar LA1910RTC 19 in. Flat Panel LCD Monitor - Answered Questions & Fixed issues

1. Try a different DVI cable. 2. Check the monitor's settings and make sure it is set to the correct resolution. 3. Try a different computer or laptop to see if the issue is with the computer or the monitor. 4. Try a different DVI port on the computer. 5. Try a different monitor. 6. Check the video card settings and make sure it is set to the correct resolution. 7. Try a different video card

Make sure it is on level ground.

No, there is no microphone listed in the specs, just integrated speakers

I use either VGA or HDMI connectors to connect to an external monitor. I'm not sure what you're asking on the "power cord". Are you asking about the charging "brick" and such? Or?

You will need to go to advanced settings under resolution options and set the display to 60hz refresh rate then go back to resolution and set your native, the problem is its probably trying to default to 75hz and is causing an issue

Try Another Monitor---If OK--Problem Is With Your Monitor---If Does The Same Thing--Problem With Computer Video.

perhaps this

Need reset on monitor BIOS. Call the support from distributors.

ivettecorral, "Switch-mode-power-supply" is in partial shutdown mode. The monitor needs you or tech to fix it. Your display isn't any different than any other brand that has BLACK and not BLANK screen!!! Read more options that you have open to you in my fixya profile. Then decide what and how you will restore unit to operational condition. 12fixlouie aka louie12fix If this helps geting you started after you do some reading, come back and rate this response on fixya!!

Try connecting another "known-good" monitor to your computer.
If it does not work, it's the video-card on your computer that is the problem.

Try connecting the monitor to the VGA-port on a laptop, or to some other desktop. If it does not work, and if it's under warranty, exercise the warranty. Otherwise, it's dead, and you need to buy a replacement, and responsibly recycle the dead monitor.

no
it is about eeprom mistake

while booting pc keep pressing F8 key, than select VGA mode in menu shown

Does it go blank before you signon, or when you sign on? If before boot to SAFE MODE and check the video display settings.. you man have settings your monitor can't understand.
If that doesn't work and you get to input your signon and then it goes blank you most likly have a virus or malware.
Log into safe mode, and use SYSTEM RESTORE to a time before you stated having the problem.
Start - All Programs - Accessories - System Tools - System Restore

It could even be that it's not plugged in to the computer, or that it's time to buy a new one.

DICEUS with 13 years experience. SIMFORM for modernizing legacy architecture. ColorWhistle for leads. PixelCrayons for tailoring to your specific needs.

Keep a backup on your hard drive or a backup. The backup system is a free service supplied by your internet provider. If you use it daily or after every update, there will never be an issue.

If you are in the middle of a contract, then cutting your wages is almost certainly a violation of your employment law rights. While I am by no means an expert on this matter, I did have a similar issue years ago - mid-contract wage cuts - and I hired anemployment attorney to fight the case on my behalf. It turned out that my employer was basically looking to scare people into taking the wage cut. They got into some pretty serious legal trouble for their transgression, and nothing happened to me in terms of wage cuts after that. If you are between contracts, your employer can re-negotiate your salary, but as far as I am aware, if you are in an agreed-upon contract, they cannot just decide to reduce your salary. If you want to settle matters, contest this action with support from a legal professional.

YouTube Backlink Generator https://ovdss.com/apps/youtube-backlink-generator

u need tally 4.5 free software (full ) if u need mail me i will give u link k

This fault / alarm / warning is not listed anywhere and the company is no longer in business. Turn over the console and see if there is a door for a back up battery. It may be warning that it is running out. Do the same with the main control unit. You could also try powering off the main unit for 10 minutes to reset the software. https://www.google.com/search?q=dukane+model+no+acc5+administrative+control+console+chirping This is the unit that drives your admin console http://serialsistemas.com.br/duk/2/85101-0025%20--%20MCS350.pdf ..