20 Most Recent Magic Chef 9122 Gas Single Oven - Page 6 Questions & Answers

thats a direct short somewhere within the oven. it happens whenoyu turn the oven on???, def check for a shorted wire, wire hitting hte cabinet of unit.

YOU NEED A NEW GAS IN VALVE BEST FITTED BY GAS FITTER /PLUMBER

Replaced ignitor on mine, fixed it.

I can't help much... When a gas burner sounds like a jet engine the chances are the gas is burning inside the mixing chamber. The gas jet directs the gas into a mixing chamber where it is mixed with the correct quantity of air before being emitted from the burner where it produces those nice blue flames. Sometimes, for a reason I don't know, ignition will cause the flame front to pass through the holes in the burner into the mixing chamber and the jet engine sound is heard. There will still be some flames from the burner but they will be weak and anaemic. The problem used to be very common in the days of coal gas but it has almost disappeared with the use of methane. I suggest you remove the burner and ensure it is clean inside and out and is a good and close fit against the gas jet and there is nothing restricting the air inlet of the mixing chamber.

Try the RV Forums. https://www.google.com/search?q=Manual+for+1984+Taurus+trailer ..

A blacksmith may be able to make the parts for you. Being over 70 years old, I doubt there will be any spares left.

Whatever is says on the temperature dial, usually about 500'F max https://www.google.com/search?q=how+hot+does+a+magic+chef+rotisserie+oven+get ..

do an online search their are hundreds of appliance part companies and sites that sell parts at discounted prices

and of course you have no manual either , neither do we

Did you end up finding the manual?

See the installation instructions, page 9. https://mcappliance.com/media/manuals/MCSWOE24S.pdf

Try this site https://searchmanuals.net/search7/?keyword=%2Bowners+%2Bmanuals&gclid=CjwKCAiAqt7jBRAcEiwAof2uKwzE1jBmBNKl9hqWd4TyeToXsj80tGOrdxRc3s6LGEWtoEA-xsOXLBoCIhQQAvD_BwE

Check each wire going to the igniter for opens. Test both ends for continuity.

I would suggest the control switch is defective.

Possible locations shown in article at the web link below: https://www.hunker.com/13409112/how-to-find-a-model-number-on-a-magic-chef-oven How to Find Model Number on Magic Chef Oven Hunker Quoting the link above: Step 1 Open the oven door. At the top, left-hand corner of the open oven, locate the model number tag. Step 2 Check under the burners. Lift each burner on the stove off to see if the plate is underneath. Do this if the plate is not located on the inside of the oven.

hope this helps a little... https://www.repairclinic.com/RepairHelp/How-To-Fix-A-Range-Stove-Oven/15-104--/Magic-Chef-Stove-burner-won-t-light

here you go... has to be item 3. hope this helps and you have a good day. go here..... https://www.repairclinic.com/RepairHelp/How-To-Fix-A-Range-Stove-Oven/16-104-82185-/new/Magic-Chef-Oven-temperature-not-accurate-59F5TXW

There is a fuse. It is on the noise filter under the outside cabinet. You would have to remove it, however, with that being said. Do not touch the capacitor if you remove the cabinet as it can kill you if you do not know what you are doing. Make sure you unplug it from its power source and wait 10 minutes or more before entering the interior. You can buy just a fuse , it is a ceramic 250 volt 20 amp fuse. Magic chef wants you to buy the noise filter with the fuse on it, part number 3518608000. Please be so careful about this, it is no joke the capacitor can kill you. Good luck and again be careful.