20 Most Recent Frigidaire Refrigerator White Fridge & Freezer Handle Set - 5304485330 - Page 7 Questions & Answers

Check the water filter, replace as needed. Remove ice bin, empty it and let it thaw out. Put it back in place and check for ice the next morning.

https://www.rohrreinigung-24notdienst.de/rohrreinigung-d%c3%bcsseldorf/

When you replaced the thermistor, did you check the resistance of the wiring and temperature sensor back at the control board? If the wires are damaged or the connector at the control board has corrosion, the control board won't get the correct signal information. If those are fine, then the control board is probably faulty. Sears Parts Direct has the control board here: https://www.searspartsdirect.com/product/3jlv6aqwdo-0046-253/id-5304512769 . Other repair shops will have this part as well. I wish that only the refrigerator temperature sensor was faulty. I hope this helps. Cindy Wells

https://www.youtube.com/watch?v=9k81fgjOk-U

you may need a check Freon level to see if its low , usually if u have low Freon level you can touch the condenser fan rails and they should be cold because when it has Freon and it liquefies into gas it creates heat hence the coils will then get warm and hot, if they are hot or warm it may not be a low Freon level issue? I would also check the freezer thermistors , see pics there may be more than 1 thermistor in freezer section , u can also check the compressor ur self to verify as not all appliance techs are reputable or knowlagable

you would need to get a whole new board to match the output pins.

Be aware the fridge works with deadly voltages. If you have not enough technical knowledge, please don't do this yourself. With a multi meter you can measure if the voltage you apply is entering the fridge. There is not much in a fridge. You find a on / of switch, a thermostat en mostly an override switch too short a thermostat. So if you measure a voltage coming is, follow the wiring and check what the thermostat does. if it won't switch you have the cause. If it does switch, follow the wiring, and if the aggregate gets a voltage and does not run, you have a defective aggregate. I can't think of more. Good Luck.

fan being obstructed behind back panel of freezer.fan motor failure or build-up of ice from door not shutting properly

The FRS26ZSH is a #for filter need MODEL #

Call the manufacture WARRENTY

Your Icemaker always makes solid cubes. Goes into bucket. your selection on the dispenser is not being recognized . Could be the control on the door (selector) . Also the selinod that switches from whole to crushed located at the assy behind bucket, Varies ON Model #

There is some truth to it. Refrigerant needs to flow from high pressure to low pressure, and refrigerant pressure is directly proportional to temperature. Once the temperature drops below 40*F, for the outdoor coil, refrigeration efficiency is lost. Some heatpump units need auxiliary heat because.
Cold refrigerant condenses, into a liquid, and a compressor will not compress liquid, why its valves and internals would chatter into pieces. There is such thing as compressor crank case heaters, or belly band heaters. A heater removes, evaporates liquid refrigerant from within a compressor, it is protection.

I would get a compressor heater, wraps around the compressor belly, near 50 watts, and can use a relay to switch off the heater when the compressor runs, or let the heater work continuously.

I DON'T KNOW. PERHAPS MOVING ARM UP AND DOWN A FEW TIMES - THEN UP AGAIN MIGHT RESET CLICKER. IF NOT, TRY UNPLUGGING AT WALL AND MOVING ARM AGAIN.

The LED above the Ice Off icon should be lit when the icemaker is disabled. It should be off when you want ice from the icemaker. To toggle the setting, press and hold the Ice Off touch pad for 3+ seconds. This is shown in the manual for the FPHF2399MF2 on page 14. Sears Parts Direct has the manual here: https://www.searspartsdirect.com/manual/234cu4elin-001428/frigidaire-fphf2399mf2-bottom-mount-refrigerator . I hope this helps. Cindy Wells

You are right! That is the most likely cause of the problem you described.

If new and under warranty contact supplier. If you attempt to fix while under warranty and cause further faults then you may void warranty.

It sounds like your ice machine is not getting enough water flow.

I would say that either the filter has split or the seal where it screws into the housing has failed. I would try a new filter and seal.

There are a number of reasons why this might be happening. You bets bet if to call a service guy out and let them take a look at it as some things require specialised equipment to troubleshoot.

Hello Brian Watkins, Not seriously able to BEGIN to help without any MODEL NUMBER... any chance you could REPOST your question... (comment or EDIT it in?? ). I have not been doing any answers on this site due to the MASSIVE SPAM and CYBER ATTACKS but I thought is was time to TRY One of my FAVORITE sites for VIDEO procedures... Give it a look (still requires MODEL NUMBER). Search Over 2 1 Million Appliance Parts