Top 20 Homelite Ignition Chip Replaces Points Condenser Xl12 Questions & Answers

Question edited for clarity and spelling.. Please don't type in all CAPS, it is classed as SHOUTING and harder to read. There is no wiring diagram for it online. It is just a mains lead, a switch and a motor. Parts schematic and a link to the company support. https://www.google.com/search?q=homelite+lawn+mower+ut13124+wiring+diagram ..

Is it in the right way? They only work in one direction. They can also be faulty from new.

It is a dinosaur is trimmer history. https://www.google.com/search?q=Homelite+ST80+string+trimmer ..

The recommended spark plug gap for a Homelite 2700 PSI pressure washer with a Champion Eco 322 spark plug is 0.030 inches. but in my opinion, It's always best to consult the owner's manual or contact the manufacturer for the most accurate and up-to-date information regarding the proper spark plug gap for your specific pressure washer model. good luck

You should have 2 lined coming from tank. A return and feed. Normally the return is the lowest positioned outlet on the carb, and the feed is at the top. When pumping the purge bulb take the gas cap off tank, and you should see fuel being returned to the tank from the return line. If not, switch the lines on carb. If still not returning fuel to the tank, you will need to pull the carb and inspect the metering and fuel pump diaphrams.

Champion RCJ-6Y or NGK BPMR7A spark plug with .025 in. electrode gap.

The recommended fuel mixture is a 50-to-1 ratio of unleaded gasoline and two-cycle engine oil, and the manufacturer recommends the use of a two-cycle oil that contains fuel stabilizer to keep the mixture fresh if you are not using it immediately.

GAP: 0.025 in. (0.63 mm).

https://www.youtube.com/watch?v=ME4r7sv2-Ks I like to buy the premix fuel with a stabilizer.

copy and paste https://documents.pub/document/homelite-st145st155st175-strimmer-and-st185st185c-brushcutter-owners-manualpdf.html

21 cc copy and paste https://www.manualslib.com/manual/767778/Jonsered-Ht21.html?page=10#manual ..

Question edited for clarity 'chainsaw'. Here is your manual https://docplayer.net/25115290-Gasoline-chain-saw-user-manual.html ..

Did you pump the primer bulb to push the gas from the tank to the carb?

$40 here https://www.lilredbarn.net/Homelite-Super-2-Chain-Saw-UT-10654-Bar-Chain-Combo-Suita-s/22414.htm All the rest are here https://www.partswarehouse.com/Homelite-Super-2-Chain-Saw-UT-10654-s/15623.htm And finally, not forgetting Jack'sSmallEngines

Homelite Super 2 Chain Saw UT-10654 Parts Diagrams

https://www.jackssmallengines.com > ... > Chain Saws Homelite Super 2 Chain Saw UT-10654 Exploded View parts lookup by model. Complete exploded views of all the ... Guide Bar Bolt. $3.56. Options Add to Cart. ..

It's not much of a manual, but a port with female threads sounds like a place that should have a threaded plug in it and is used from draining down in winter to stop freezing water cracking the pump. https://manuals.homelite.com/system/files/6687/original/UT80993A_723_QRG_eng_01.pdf?2017 Here are parts. Part 17 is Drain Plug Bolt. https://www.ereplacementparts.com/homelite-ut80522b-2700-psi-gas-pressure-washer-parts-c-18807_131787_202598.html ..

take plug out and see if you have spark then spray a little starting fluid in the hole and quickly put plug back in and try to start it again

0.025 in. (0.63 mm)

Perhaps you can follow these simple steps to solve your problem:

Start and let the saw run until its run out due to empty gas. Take off the cylinder cover, which sits on top of the saw. Using the needle nose pliers grab the rear end of the fuel line and gently pull it off the carburetor.

Remove the gas filler cap from the tank. Use the needle nose pliers to grab the fuel filter in the bottom of the tank. Pull out the fuel filter and the entire fuel line from the saw. Use the pliers to pinch the fuel line and with your hand pull the fuel filter off the fuel line. Throw both of these away.

Cut off about 10 inches of new fuel line and insert the metal wire into the fuel line. Push the wire and fuel line into the gas tank and through the hole at the bottom until you see the line come out near the carburetor. Don't connect it to the carburetor yet.

Pull the metal wire out of the line and cut off any excess line with the scissors. Pull it back out of the tank slightly and insert the fuel filter into the fuel line. Push them back into the tank.Use the needle nose pliers to grab the rear end of the fuel line and attach it to the carburetor.

I hope these helps. ??