Stanley 2350 PSI 5 HP 2.3 GPM Gas Pressure Washer - Non CA - Answered Questions & Fixed issues
Stanley 10-801 utility knife. How
On the pivot end of the bladed knife is a black plug that says pull. They actually mean "Push". push it away from the knife body and rotate the handle half it's mounted in, down. The body will rotate in half , revealing the utility blade and more blades in the rear storage.Also note the blade depth adjustment has a locking detent. You have to push it to the right to unlock the utility blade.and push it to the right when retracting to fully retract and lock the utility blade.
6/14/2019 1:15:31 AM •
Stanley Garden
•
Answered
on Jun 14, 2019
•
2,314 views
Stanley P1800S pressure washer lost pressure after a few uses
The valve-o-rings + [ parbaks seals ] where the pressure can be adjusted with.
Control the water inlet filter or hose that there are no waterlock couplers are used or is mounted
on the wrong site on the hose , that it is used as water inlet on the tap.
12/25/2016 4:53:59 PM •
Stanley Garden
•
Answered
on Dec 25, 2016
•
155 views
How do I get the top off? STUCK!
Hi Chris:
It is usually easiest to rest the weight on the tailgate of a pickup truck (or some other device) and then slip out of the harness.
Another technique is to lift bend forward while at the same time rising one shoulder and lowering the other. That will create "slack" on the low shoulder side allowing you to get that arm out.
Cheers
3/19/2016 6:31:49 PM •
Stanley Garden
•
Answered
on Mar 19, 2016
•
885 views
How do I know if
Gerard, PLEASE contact me at (941) 391-5152 or
[email protected] so I can hire you to replace the batteries in my Stanley barflex bf0109 light like you did above with vastly more run time mAh. I need someone to do it for me. I'm disabled. I just joined fixya.
Thanks,
Wallace Franklin Banach...
11/14/2015 11:56:33 AM •
Stanley Garden
•
Answered
on Nov 14, 2015
•
673 views
What is the lance o ring for
If you switch the unit on and water spits out of a connection, that's where you either put the O-rings or replace them.
9/21/2014 1:23:00 PM •
Stanley Garden
•
Answered
on Sep 21, 2014
•
127 views
The stanley garage door opener Model 3220.51 is
If it is a screw drive like mine all I needed to do was lube up the screw with a product called "fluid film" and all was ok. The screw was binding making the sensor think the door was blocked and it would go back up.
12/23/2013 10:18:11 PM •
Stanley Garden
•
Answered
on Dec 23, 2013
•
3,178 views
I have a 500 amp
No you do not. You are supposed to charge it for 24 hours before the first initial use. After that you are supposed to charge after it using it to jump start a vehicle or every 30 days if not used at all.You are supposed to charge until the two red and one green LED lamps are lit SOLID. The unit should be fully charged once the LEDs are lit solid. Unplug the unit and put back into storage until needed. Again if not used for extended periods of time the unit should be charged ever 30 days.
12/3/2012 1:47:15 AM •
Stanley Garden
•
Answered
on Dec 03, 2012
•
432 views
How do I install a
View the video below showing how to do it. This video shows the bottom wheel but the top parts install in the exact same way.http://www.youtube.com/watch?v=vYa0Hlk0Uu8 WebRepOverall ratingThis site has no rating(not enough votes)
11/9/2012 10:37:50 AM •
Stanley Garden
•
Answered
on Nov 09, 2012
•
514 views
How to change the battery
On the back of the unit in the left down corner are two screws. The bottom one (smallest) of the two has to be removed and then you can slide out the bottom part where the batteries are.Good luck.
8/2/2012 12:26:37 PM •
Stanley Garden
•
Answered
on Aug 02, 2012
•
1,202 views
I have a stanley SD350
Mine is doing the same thing. Did you get your problem resolved and if so what did you do? Thanks
12/10/2011 3:23:34 PM •
Stanley Garden
•
Answered
on Dec 10, 2011
•
1,387 views
Not finding what you are looking for?